Go Back   Infamous Nissan - Hardbody / Frontier Forums > Search Forums

Showing results 1 to 25 of 500
Search took 0.12 seconds.
Search: Posts Made By: jp2code
Forum: Hardbody Forum (D21) 09-22-2022, 03:52 PM
Replies: 22
Views: 250
Posted By jp2code
The fuel pump should run until the fuel line...

The fuel pump should run until the fuel line reaches fuel pressure; then it shuts off.

If you hear it power on when you turn the ignition key to ON (not cranking), then it should be fine.

If...
Forum: Hardbody Forum (D21) 09-16-2022, 04:33 PM
Replies: 24,073
Views: 1,971,203
Posted By jp2code
I've had the 16-inch tires on for about a week. ...

I've had the 16-inch tires on for about a week.

The steering felt a little squirrelly after having the 18-inch Titans on.

I know the Titans had a different offset, and I had the front end...
Forum: Hardbody Forum (D21) 09-12-2022, 01:26 PM
Replies: 24,073
Views: 1,971,203
Posted By jp2code
My 2 favorites ...

My 2 favorites

https://i.imgur.com/MdCIjfah.jpg
Forum: Hardbody Forum (D21) 09-10-2022, 12:37 PM
Replies: 3
Views: 71
Posted By jp2code
Does this happen every time, just when cold, just...

Does this happen every time, just when cold, just when warm?

What have you done to the engine lately?
Forum: Hardbody Forum (D21) 09-09-2022, 09:21 PM
Replies: 10
Views: 131
Posted By jp2code
Your A/C belt should be a lot like this one: ...

Your A/C belt should be a lot like this one:
(keep in mind that I have a V6, not the 4-cylinder)
qw5iCS4qCDw

In the image you posted above, it looks like you are showing a spring tensioner.
...
Forum: Hardbody Forum (D21) 09-09-2022, 08:01 PM
Replies: 10
Views: 131
Posted By jp2code
Put a wrench on the big bolt on the pulley that...

Put a wrench on the big bolt on the pulley that your hand is covering. There should be a built-in spring in it to allow you to get tension on the belt.
Forum: Engine and Drivetrain 09-09-2022, 07:30 PM
Replies: 168
Views: 1,260
Posted By jp2code
If you have a small, 1/4-inch drive ratchet and a...

If you have a small, 1/4-inch drive ratchet and a wobble extension, you should be able to get in there.

But, I don't have a 4-cylinder. I don't know what you are looking at.
Forum: Hardbody Forum (D21) 09-09-2022, 01:14 AM
Replies: 24,073
Views: 1,971,203
Posted By jp2code
P&B: https://www.ebay.com/itm/162870692852 ...

P&B:

https://www.ebay.com/itm/162870692852
https://www.ebay.com/itm/194690305203

I got a set of those on bottom for my Xterra wheels. The factory Nissan quality isn't there, but they are about...
Forum: Hardbody Forum (D21) 09-08-2022, 09:47 PM
Replies: 24,073
Views: 1,971,203
Posted By jp2code
Jeez. Good thing I'm not making my truck receive...

Jeez. Good thing I'm not making my truck receive popular opinion.

They are NOT going back on, because I don't like them.

I'm also not putting Pathfinder mirrors on ...and I'm not lowering it.
...
Forum: Engine and Drivetrain 09-08-2022, 03:40 PM
Replies: 168
Views: 1,260
Posted By jp2code
> might it be a good idea to re-install old fuel...

> might it be a good idea to re-install old fuel injectors
> temporarily since truck was able to idle when they
> were in place?

That can't hurt. It's a big pain to do with the VG30e engine, but...
Forum: Wiring and Electrical 09-08-2022, 11:08 AM
Replies: 197
Views: 42,391
Posted By jp2code
That's a cool PDF. Be sure to snag that one,...

That's a cool PDF.

Be sure to snag that one, Deerhurst.
Forum: Engine and Drivetrain 09-08-2022, 11:06 AM
Replies: 23
Views: 313
Posted By jp2code
> I will definitely check those. When you...

> I will definitely check those.

When you are tightening the nuts (since there are 4 of them), be sure to "walk" the nuts on so the bottom plate does not twist on you.

By that, I mean get each...
Forum: Engine and Drivetrain 09-08-2022, 10:50 AM
Replies: 168
Views: 1,260
Posted By jp2code
I got you now. So 0.9 Volts on your meter? I...

I got you now. So 0.9 Volts on your meter? I think 9 mV would be 0.009 Volts.

And I thought you were testing the ground-to-ground wire.
Forum: Engine and Drivetrain 09-07-2022, 07:23 PM
Replies: 23
Views: 313
Posted By jp2code
That sounds like the U-Bolts are loose. They are...

That sounds like the U-Bolts are loose. They are supposed to be torqued down to 65 - 72 ft-lbs. Imagine lifting enough to pick up a 75-lb dumbbell at the gym. That's how much you have to pull on each...
Forum: Hardbody Forum (D21) 09-07-2022, 04:25 PM
Replies: 24,073
Views: 1,971,203
Posted By jp2code
I've got some little "high speed" mud flaps in...

I've got some little "high speed" mud flaps in the back, but there is nothing to mount them to up front.

I did get my tires installed today, and the warranty says they are good for 50k miles. My...
Forum: Engine and Drivetrain 09-07-2022, 10:58 AM
Replies: 23
Views: 313
Posted By jp2code
The driveshaft has a yolk that slides freely in...

The driveshaft has a yolk that slides freely in and out of the transmission shaft. That is by design so that when your engine twists under load or you hit bumps, the driveshaft does not smack into...
Forum: Engine and Drivetrain 09-07-2022, 10:52 AM
Replies: 168
Views: 1,260
Posted By jp2code
The ground wire should read 0 Volts whether the...

The ground wire should read 0 Volts whether the MAF is plugged in or not. That wire should always go to ground.

The KA24e doesn't have the same problems as the VG30e. On the V6, the MAF is at the...
Forum: Hardbody Forum (D21) 09-06-2022, 10:12 PM
Replies: 24,073
Views: 1,971,203
Posted By jp2code
Finally taking those ugly fender flares off. With...

Finally taking those ugly fender flares off. With the 18-inch Titans, I needed them to keep mud and road grim from flinging all over the truck and windshield. With the Titans, I had smaller tires...
Forum: Engine and Drivetrain 09-06-2022, 09:39 PM
Replies: 23
Views: 313
Posted By jp2code
What size are your tires? 195/75R14 is a lot...

What size are your tires? 195/75R14 is a lot smoother than 225/40R17.

Other than that, it *IS* a truck. It has a 1/2-ton suspension unless you have the Heavy Duty Long Bed like mine: It has the...
Forum: Engine and Drivetrain 09-06-2022, 09:37 PM
Replies: 168
Views: 1,260
Posted By jp2code
The shielding wire should be grounded. Measuring...

The shielding wire should be grounded. Measuring from ground to the shielding wire should have 0 milliVolts. If it does not, my guess is the shielding wire is not grounded very well.
Forum: Engine and Drivetrain 09-06-2022, 07:14 PM
Replies: 23
Views: 313
Posted By jp2code
While waiting on the U joints and carrier bearing...

While waiting on the U joints and carrier bearing to arrive, you can swap tires around on your truck (like put the fronts on the back). If the problem moves to the front, cancel the order for the...
Forum: Hardbody Forum (D21) 09-06-2022, 07:11 PM
Replies: 20
Views: 333
Posted By jp2code
Avoid Rebuilt. Buy a new one. Any brand name is...

Avoid Rebuilt. Buy a new one. Any brand name is usually better than one that just says "New Starter".
Forum: Engine and Drivetrain 09-06-2022, 06:59 PM
Replies: 168
Views: 1,260
Posted By jp2code
I can't help you on this. I've never owned a...

I can't help you on this. I've never owned a 4-cylinder.

You might try asking in one of the threads where they talk about doing the KA24e Timing Chain swap or the thread What have you done to your...
Forum: Engine and Drivetrain 09-06-2022, 10:52 AM
Replies: 13
Views: 202
Posted By jp2code
There is one now as part of the radiator. I'm...

There is one now as part of the radiator. I'm guessing yours had that too. Do you run both (radiator output goes to external cooler input), or bypass the build-in cooler in the radiator?
Forum: Introductions 09-06-2022, 12:57 AM
Replies: 22
Views: 294
Posted By jp2code
> I am thinking it is 1/4"-28 I certainly...

> I am thinking it is 1/4"-28

I certainly don't know, but I bet it's metric - like M6 or something
Showing results 1 to 25 of 500

 
Forum Jump

All times are GMT. The time now is 03:20 PM.


Powered by vBulletin® Version 3.8.6
Copyright ©2000 - 2022, Jelsoft Enterprises Ltd.