Go Back   Infamous Nissan - Hardbody / Frontier Forums > Search Forums

Showing results 1 to 25 of 500
Search took 0.06 seconds.
Search: Posts Made By: Deerhurst
Forum: Hardbody Forum (D21) Yesterday, 10:37 PM
Replies: 23,219
Views: 1,709,089
Posted By Deerhurst
The beams MUST be aligned with low beam up and...

The beams MUST be aligned with low beam up and high beam down. It's how the housing is designed to handle light. Not saying this will make anything better or worse but a H4 always has low beam on the...
Forum: Hardbody Forum (D21) 07-29-2021, 10:32 PM
Replies: 3
Views: 46
Posted By Deerhurst
There is a fuse that does the dash. My truck...

There is a fuse that does the dash. My truck blows it when the reverse lights come on with a trailer plugged in. I don't remember which one but it isn't marked as such.



Is your voltage...
Forum: Engine and Drivetrain 07-29-2021, 07:56 PM
Replies: 3
Views: 26
Posted By Deerhurst
That 97 may not be happy with an EGR delete...

That 97 may not be happy with an EGR delete though the EGR is a terrible idea.



I'm fairly positive that the flange will bolt on fine.
Forum: Hardbody Forum (D21) 07-29-2021, 02:40 AM
Replies: 14
Views: 205
Posted By Deerhurst
Pull codes, check vacuum lines.

Pull codes, check vacuum lines.
Forum: Engine and Drivetrain 07-29-2021, 01:30 AM
Replies: 7
Views: 72
Posted By Deerhurst
I think I have a retrofit guide or writeup around...

I think I have a retrofit guide or writeup around here. Mine is a little special because I got the largest projectors I could find instead of ones that will drop in.



If you just get the...
Forum: Engine and Drivetrain 07-29-2021, 01:28 AM
Replies: 3
Views: 26
Posted By Deerhurst
The header for the 95 may not have all of the...

The header for the 95 may not have all of the emissions ports the 97 requires. Being a 97 it is OBD compliant and might complain with the emissions stuff not correctly plumbed. If you are OK with...
Forum: Hardbody Forum (D21) 07-28-2021, 08:00 PM
Replies: 59
Views: 1,927
Posted By Deerhurst
With a new clutch do as much shifting at speed as...

With a new clutch do as much shifting at speed as possible for the first 3-5k miles to bed it in nice. Avoid slipping it as much as possible.



Glad it's working awesome!
Forum: Hardbody Forum (D21) 07-28-2021, 04:46 PM
Replies: 14
Views: 205
Posted By Deerhurst
Gl5 is bad. It'll eat your synchros. Gl4 is good.

Gl5 is bad. It'll eat your synchros. Gl4 is good.
Forum: Hardbody Forum (D21) 07-27-2021, 07:48 PM
Replies: 14
Views: 205
Posted By Deerhurst
Have it replaced or replace it yourself? Labor is...

Have it replaced or replace it yourself? Labor is expensive. The parts are cheap. Have the clutch, pressure plate and throw out bearing replaced. Have the flywheel inspected. It might need...
Forum: Engine and Drivetrain 07-27-2021, 03:21 AM
Replies: 2
Views: 30
Posted By Deerhurst
I wouldn't hesitate to put it on a trailer. Just...

I wouldn't hesitate to put it on a trailer. Just drive carefully, as always.
Forum: Engine and Drivetrain 07-26-2021, 01:17 AM
Replies: 8
Views: 63
Posted By Deerhurst
Honestly I'm not sure. Caddie might be the best...

Honestly I'm not sure. Caddie might be the best source on that.
Forum: Engine and Drivetrain 07-25-2021, 05:43 PM
Replies: 8
Views: 63
Posted By Deerhurst
Yes, the wave plate can cause issues but is...

Yes, the wave plate can cause issues but is likely OK if you have spark. I think one guy found his MAF was bad so it wasn't throwing fuel.



Have you checked codes?


Age isn't an issue. If...
Forum: Hardbody Forum (D21) 07-25-2021, 04:37 PM
Replies: 20
Views: 201
Posted By Deerhurst
I completely disagree with the Haynes being...

I completely disagree with the Haynes being useful. I have all 3, Haynes, Chilton's, FSM. I tried using the Haynes once, it didn't have the basic info I needed (I think it was for the timing belt)...
Forum: Engine and Drivetrain 07-25-2021, 04:33 PM
Replies: 7
Views: 72
Posted By Deerhurst
I'd skip the KN filter. Your engine cannot pull...

I'd skip the KN filter. Your engine cannot pull enough air to make a high flow filter useful. You'll be trading filtration for no gain as the oil type filters tend to filter much poorer than paper...
Forum: Engine and Drivetrain 07-25-2021, 04:03 AM
Replies: 8
Views: 63
Posted By Deerhurst
Dona search. So.eoje just solved a very very...

Dona search. So.eoje just solved a very very similar issue earlier this week.
Forum: Hardbody Forum (D21) 07-25-2021, 01:48 AM
Replies: 23,219
Views: 1,709,089
Posted By Deerhurst
The ash tray cupholder is a little off for my...

The ash tray cupholder is a little off for my truck but I've been told there are a couple different ashtray sizes for the square dash.



It's a LOT bigger than it looks.
Forum: Hardbody Forum (D21) 07-24-2021, 11:58 PM
Replies: 20
Views: 201
Posted By Deerhurst
Sorry to be the bearer of bad news but the haynes...

Sorry to be the bearer of bad news but the haynes is worthless for the D21. It kinda covers some things. The Chilton's is awesome as is the FSM. The Haynes is about half the thickness of the...
Forum: Hardbody Forum (D21) 07-23-2021, 07:56 PM
Replies: 20
Views: 201
Posted By Deerhurst
What motor? Z24 or VG30? ...

What motor? Z24 or VG30?







I mostly fix what breaks.
Forum: Hardbody Forum (D21) 07-23-2021, 04:15 AM
Replies: 52
Views: 546
Posted By Deerhurst
Most of us use imgur.

Most of us use imgur.
Forum: Hardbody Forum (D21) 07-23-2021, 03:30 AM
Replies: 52
Views: 546
Posted By Deerhurst
Hell yeah! Good work!! I will...

Hell yeah! Good work!!



I will probably be picking your brain at some point when I MPFI convert.
Forum: Hardbody Forum (D21) 07-22-2021, 03:43 AM
Replies: 8
Views: 104
Posted By Deerhurst
It uses the same lifters as the VG30. Lifters on...

It uses the same lifters as the VG30. Lifters on these engines are a PITA. Sometimes it's impossible to make them quiet. I'd just go with a recognized brand.





If you ever want to get rid...
Forum: Hardbody Forum (D21) 07-22-2021, 02:31 AM
Replies: 8
Views: 104
Posted By Deerhurst
Good luck! Let us know what you find!

Good luck! Let us know what you find!
Forum: Hardbody Forum (D21) 07-22-2021, 02:30 AM
Replies: 17
Views: 190
Posted By Deerhurst
The quote button doesn't want to play nice on...

The quote button doesn't want to play nice on mobile for me but this is a replay to you, JP.





Let's assume it's turning over slowly. Let's also assume the battery voltage checks out OK at...
Forum: Hardbody Forum (D21) 07-21-2021, 11:33 PM
Replies: 17
Views: 190
Posted By Deerhurst
With electric motors voltage is RPM and current...

With electric motors voltage is RPM and current is torque.
Forum: Hardbody Forum (D21) 07-21-2021, 09:49 PM
Replies: 23,219
Views: 1,709,089
Posted By Deerhurst
You can drill holes in glass. I drill holes I'd...

You can drill holes in glass. I drill holes I'd harder and more brittle things all the time!
Showing results 1 to 25 of 500

 
Forum Jump

All times are GMT. The time now is 04:59 AM.


Powered by vBulletin® Version 3.8.6
Copyright ©2000 - 2021, Jelsoft Enterprises Ltd.