Go Back   Infamous Nissan - Hardbody / Frontier Forums > Model Specific > Hardbody Forum (D21)

Reply
 
Thread Tools Display Modes
Old 06-09-2018, 09:08 AM   #21
XoXSciFiGuy
 
XoXSciFiGuy's Avatar
 
Join Date: May 2017
Location: Auburn, WA
Posts: 1,058
Vehicle: 1997 D21 King Cab XE 2WD
Thanks: 39
Thanked 147 Times in 135 Posts
Default

Another trick is to do your brakes fully....ONE side at a time. That way you can go back to the other one and look to see how it goes back together.

Back brakes last longer than front pads because when you stop, you also put most of the vehicle weight forward, wearing the front faster than the rear.
__________________

1997 King Cab XE, 5-sp, canopy, AC/PS, KA24E, 112,000 miles. Need a technical manual? Drop me a message. Chilton's for amateurs.
XoXSciFiGuy is offline   Reply With Quote
Old 06-12-2018, 12:03 AM   #22
nothingtoseehere
 
Join Date: Jan 2018
Location: the woods
Posts: 45
Vehicle: 1987 z24i 4x4
Thanks: 20
Thanked 3 Times in 2 Posts
Default

i used the truck around the farm today, pretty short, heavy hauls, minimal breaking, no heat to the left pad by the end of the day, doesn't really say much. i will probably just find new calipers, but am curious whether or not the work i did actually freed up some minor build up from sitting so much this winter.


thanks for all the help in understanding this system.



now...

what's with the squealing belt sound when the steering wheel is turned to extreme left or extreme right? there is sufficient and clean power steering fluid...
nothingtoseehere is offline   Reply With Quote
Old 06-12-2018, 12:04 AM   #23
nothingtoseehere
 
Join Date: Jan 2018
Location: the woods
Posts: 45
Vehicle: 1987 z24i 4x4
Thanks: 20
Thanked 3 Times in 2 Posts
Default

p.s. i still can't figure out the diagnostics, nothing seems to get the thing to stop flashing 11, 22, 33, 44, 55, 66 repeatedly into perpetuity....
nothingtoseehere is offline   Reply With Quote
Old 06-12-2018, 12:36 AM   #24
SBJ
Total Buzzkill
 
Join Date: Nov 2016
Location: OR
Posts: 1,558
Vehicle: '90 D21 4cyl 5spd 2wd
Thanks: 166
Thanked 178 Times in 163 Posts
Default

Your ECU is cycling through the different diagnostic modes repeatedly. It'll do that until you select one. The trick is to turn the dial or flip the switch back once it's on the one you want (in this case, probably 3 or 5). Jp2code has a good video in his signature on how to check codes.

New calipers are not too bad online...I think I paid around $70 shipped for both.

The belt squealing has to do with it slipping when there's an excessive load on the power steering system. You could try tightening up the belt a little bit and see if it helps. The noise could also be coming from the pump itself but that's usually more of a whine than a squealing noise. It's normal to have a bit of steering noise when the wheel is turned all the way in one direction.

Hope this helps!
SBJ is offline   Reply With Quote
Thanked by:
nothingtoseehere (06-23-2018)
Old 06-12-2018, 02:09 AM   #25
jp2code
Software Developer
 
jp2code's Avatar
 
Join Date: Dec 2011
Location: Longview, TX [USA]
Age: 49
Posts: 8,588
Vehicle: 94 LB 2x4 Manual VG33e
Thanks: 1,224
Thanked 1,074 Times in 946 Posts
Default

Link to video is below. Your ECU should be more like the video that Deerhurst provided, but I think my video goes into more detail.
__________________
Joe (not a mechanic!) Don't have an account? EMAIL ME
Free Service Manuals: https://ownersmanuals2.com/make/nissan
Walk-through: Checking Nissan Trouble Codes
1994 VG30E to VG33E with H256 Cams

jp2code is offline   Reply With Quote
Old 06-12-2018, 04:26 AM   #26
Deerhurst
4/86 SE-V6 2 tone 4x4 HB
 
Deerhurst's Avatar
 
Join Date: Apr 2013
Location: Oregon
Posts: 5,103
Vehicle: 1986.5 Hardbody
Thanks: 703
Thanked 467 Times in 433 Posts
Default

The old ECM like mine is very very simple and not well documented.



Yours is basically better than mine in every way. It also have 5 modes. You can monitor your A/F ratios, TPS, etc all the way to pulling codes. You can also do a remote code display. You will turn the dial to the mode you want then read what it shows you. The FSM should show that. I believe the Chilton's does too.



Mine has an unlabeled switch that you have to guess which way is codes. And your ECM has a bunch of internal improvements such as static memory. Mine forgets everything when you turn off the key. Yours can retain info. Stuff like that.
__________________
1986.5 SE-V6 4X4 D21 Hardbody
Pacesetter Long Tube Headers
Morimoto Mini D2S HID Projectors and Hella 500s
VG33i
Deerhurst is offline   Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT. The time now is 09:56 AM.


Powered by vBulletin® Version 3.8.6
Copyright ©2000 - 2018, Jelsoft Enterprises Ltd.