Go Back   Infamous Nissan - Hardbody / Frontier Forums > Tech Area > Suspension

Reply
 
Thread Tools Display Modes
Old 05-09-2019, 09:50 AM   #1
joe77
Banned
 
Join Date: May 2019
Location: india
Posts: 1
Vehicle: 2014
Thanks: 0
Thanked 0 Times in 0 Posts
Default upper control arm lift

Hello everyone,

ive noticed that in the suspension lift kits the upper control for the hardbody is pretty much longer in length giving it the ground clearance. is there another manufacture that makes a longer arm that can bolt on to make it get the clearance (3-4in) or am i stuck paying 250$ to 500$ plus, and leaf spring can i not just and another leaf to the system to jack up the rear end so im not squating the truck https://scrabblewordfinder.vip/ https://www.applock.ooo/ https://www.7zip.vip/


ps i have a 1993 HB 4cylnder base 2 wheel drive

Thanks!

Last edited by joe77; 05-12-2019 at 07:57 PM.
joe77 is offline   Reply With Quote
Old 05-09-2019, 03:14 PM   #2
ahardb0dy
The Post Count Whore
 
ahardb0dy's Avatar
 
Join Date: May 2014
Location: Sorrento, Florida
Age: 53
Posts: 7,404
Vehicle: 2017 Nissan Frontier Desert Runner
Thanks: 63
Thanked 871 Times in 803 Posts
Default

Welcome to Infamous.


The aftermarket upper control arms are not longer to provide lift, they are designed at a different angle so when you adjust the torsion bars to get more lift the front end can still be aligned.


Yes, there is a difference in the length between the 2wd and 4wd upper control arms, and they are not interchangeable (4wd arms are longer).


Your not going to get 3-4 inches of lift in the front, 2 or 4 wheel drive, most of the suspension kits will say you can get about 2" of lift, once again, the lift is obtained by adjusting (cranking up) the torsion bars. The aftermarket arms also alter the angle the ball joint sits at so it doesn't bind up and as I said allows you to align the truck.


If you were to install 4wd upper arms on your 2wd truck you will not be able to align it, someone one time bought the wrong arms and he could not get the front end any where close to being aligned properly.


Also keep in mind, you may be able to adjust the torsion bars to get more than 2 inches of lift but that would put the upper control arm right against the rubber bump stops, which would totally eliminate any downward suspension travel and would cause the truck to ride like crap, being 2wd you would not have to worry about the CV axles being at a steep angle, something that happens when the front is cranked up too high.


For the rear, the 2wd has the leaf springs mounted under the axle tube (4wd they are on top), you can do an add a leaf to "re arc" the springs, which will provide some lift, you can replace the leaf springs with new ones that are made to provide lift, you can use a pair of longer shackles to give some lift ( or a combination of add a leaf or shackles. You can not use a block as I said the springs being under the axle tube, a block would cause the rear to be lower, the block moving the axle up ( the way a 2wd is lowered in the rear).


Normally the front end sits lower than the rear so not the same amount of lift is needed in the rear to bring the truck to sitting level.
__________________
My name is Tony and I'm a Infamousaholic

Current truck - 2017 Nissan Frontier Desert Runner ,

(formerly owned: 1993 Nissan Hardbody king cab 2wd, 90 Nissan Sentra, 94 Nissan Pathfinder SE 4x4, 05 Nissan Titan, 87 Nissan SE-V6 4x4 king cab, 94 Infiniti Q45t & 80 Datsun 310GX )
ahardb0dy is offline   Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT. The time now is 08:08 AM.


Powered by vBulletin® Version 3.8.6
Copyright ©2000 - 2019, Jelsoft Enterprises Ltd.