Go Back   Infamous Nissan - Hardbody / Frontier Forums > Tech Area > Wiring and Electrical

Reply
 
Thread Tools Display Modes
Old 01-15-2018, 07:54 PM   #1
grnsierra01
 
Join Date: Jan 2018
Location: NC
Posts: 4
Vehicle: Nissan Hardbody 1996
Thanks: 0
Thanked 0 Times in 0 Posts
Default How do you remove a connector pin?

I just bought a 1996 HB that was throwing a P1130 DTC. After reading several threads on this forum, I checked the wiring harness to see if I was getting 12 volts to the solenoid and found that the voltage would fluctuate if i moved the black and white wire. I decided to follow it in the harness to the 8 pin connector behind the battery on the passenger side inner fender, but now I cannot get the pin out of the connector so that I can replace the wire.

What do I have to press, plug in, etc., to get the pins out of this connector?

Thanks, Jason
Attached Images
File Type: jpg connector.jpg (93.8 KB, 5 views)
grnsierra01 is offline   Reply With Quote
Old 01-15-2018, 08:11 PM   #2
ahardb0dy
The Post Count Whore
 
Join Date: May 2014
Location: Sorrento, Florida
Age: 52
Posts: 7,004
Vehicle: 1993 Nissan Hardbody
Thanks: 58
Thanked 775 Times in 724 Posts
Default

You need to insert something small, a small flat head screw driver or a skinny awl under the bottom of the metal connector, see below:

https://youtu.be/2mW-ieXEP1M
__________________
My name is Tony and I'm a Infamousaholic

Current truck - 1993 Nissan Hardbody king cab 2wd
, (formerly owned: 90 Nissan Sentra, 94 Nissan Pathfinder SE 4x4, 05 Nissan Titan, 87 Nissan SE-V6 4x4 king cab, 94 Infiniti Q45t & 80 Datsun 310GX )
ahardb0dy is offline   Reply With Quote
Old 01-15-2018, 09:42 PM   #3
grnsierra01
 
Join Date: Jan 2018
Location: NC
Posts: 4
Vehicle: Nissan Hardbody 1996
Thanks: 0
Thanked 0 Times in 0 Posts
Default

Actually, that blue thing in the middle was a lock and I finally got it to come out and the pim came right out. Now my problem is that this wire seems to be fine now.

I checked it with a 9v battery and my voltmeter and I cant get it to drop voltage but I tested many times while in and out of the wire loom before I started removing the pins. I even checked the bulkhead connector before pulling the wire out of the loom and it gave a steady 12v even with shaking it.

Im going to replace the wire put I figure with my bad luck, this will not be the solution to my problem.
grnsierra01 is offline   Reply With Quote
Old 01-15-2018, 11:39 PM   #4
grnsierra01
 
Join Date: Jan 2018
Location: NC
Posts: 4
Vehicle: Nissan Hardbody 1996
Thanks: 0
Thanked 0 Times in 0 Posts
Default

Ok, new problem...where can I get the terminal ends that match the ones on the old wire?
grnsierra01 is offline   Reply With Quote
Old 01-16-2018, 02:20 AM   #5
ahardb0dy
The Post Count Whore
 
Join Date: May 2014
Location: Sorrento, Florida
Age: 52
Posts: 7,004
Vehicle: 1993 Nissan Hardbody
Thanks: 58
Thanked 775 Times in 724 Posts
Default

http://www.wiringspecialties.com/ka24de2.html#
__________________
My name is Tony and I'm a Infamousaholic

Current truck - 1993 Nissan Hardbody king cab 2wd
, (formerly owned: 90 Nissan Sentra, 94 Nissan Pathfinder SE 4x4, 05 Nissan Titan, 87 Nissan SE-V6 4x4 king cab, 94 Infiniti Q45t & 80 Datsun 310GX )
ahardb0dy is offline   Reply With Quote
Old 01-16-2018, 02:31 AM   #6
dvdswan
Super Moderator
 
dvdswan's Avatar
 
Join Date: Mar 2009
Location: Port Orchard, WA
Posts: 4,389
Vehicle: 96 HB
Thanks: 148
Thanked 568 Times in 502 Posts
Default

https://www.summitracing.com/parts/p...iABEgK0j_D_BwE

there is a clip that locks the connector in the housing. use the thin skinny one, it will release the clip and you can pull the wire and connector out.

similar to this... https://www.youtube.com/watch?v=5xIEpYNTHFk
__________________
Dave
96 HB XE
SAS'd D44 3-link on 35s
http://www.cardomain.com/ride/2618002
dvdswan is offline   Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT. The time now is 01:10 PM.


Powered by vBulletin® Version 3.8.6
Copyright ©2000 - 2018, Jelsoft Enterprises Ltd.