Go Back   Infamous Nissan - Hardbody / Frontier Forums > Tech Area > Wiring and Electrical

Reply
 
Thread Tools Display Modes
Old 01-22-2015, 02:35 AM   #1
kenmack
 
Join Date: Jan 2015
Location: Edgeoftown
Posts: 24
Vehicle: Hardbody 1989
Thanks: 0
Thanked 0 Times in 0 Posts
Default Fusible Link Melts

While troubleshooting my 1989 KC 4x4 6cyl which would not start, I found the fusible link to have one melted green wire. The not starting problem was solved with a new starter. I also replaced the fusible link. This was a couple of weeks ago.

I noticed today that the fusible link had fried one of it's green wires again. Here are some more facts:

The old fusible link seemed to have not recently melted.

I cannot see that anything is not working when the link was melted.

The starter was replaced before the new link came in and everything seemed to work fine and the truck was operable before the new link was installed.

The new link melted at an undetermined time, but I again cannot see that anything is not working.

My principles want to fix the cause and then replace the link, yet it seems that nothing is wrong otherwise as everything seems to be working fine. What might be wrong?
kenmack is offline   Reply With Quote
Old 01-22-2015, 08:31 AM   #2
ahardb0dy
The Post Count Whore
 
Join Date: May 2014
Location: Sorrento, Florida
Age: 52
Posts: 7,004
Vehicle: 1993 Nissan Hardbody
Thanks: 58
Thanked 775 Times in 724 Posts
Default

Are their 2 green fusible links? The FSM shows 2 green, one seems to go to the ECU, the other one to the ignition switch/ No idea what the one going to the ECU is for.
__________________
My name is Tony and I'm a Infamousaholic

Current truck - 1993 Nissan Hardbody king cab 2wd
, (formerly owned: 90 Nissan Sentra, 94 Nissan Pathfinder SE 4x4, 05 Nissan Titan, 87 Nissan SE-V6 4x4 king cab, 94 Infiniti Q45t & 80 Datsun 310GX )
ahardb0dy is offline   Reply With Quote
Old 01-22-2015, 09:47 AM   #3
kenmack
 
Join Date: Jan 2015
Location: Edgeoftown
Posts: 24
Vehicle: Hardbody 1989
Thanks: 0
Thanked 0 Times in 0 Posts
Default

The link is one piece but has two brown and two green wires. My diagram has one going to the ECU. Maybe for power? The other one goes to the ignition switch, then branches to some relays and then the fuse box. All systems on the indicated fuses are operational.

In some of my reading, I've come across a person having his link melt when his alternator was not grounded properly and was likely back feeding. I will check my connections there in the morning, but I don't really think I will find anything there as I've not been messing with it lately.
kenmack is offline   Reply With Quote
Old 01-05-2017, 03:43 AM   #4
kenmack
 
Join Date: Jan 2015
Location: Edgeoftown
Posts: 24
Vehicle: Hardbody 1989
Thanks: 0
Thanked 0 Times in 0 Posts
Default

Bump in case anyone has any new insight.
kenmack is offline   Reply With Quote
Old 01-28-2018, 12:32 AM   #5
kenmack
 
Join Date: Jan 2015
Location: Edgeoftown
Posts: 24
Vehicle: Hardbody 1989
Thanks: 0
Thanked 0 Times in 0 Posts
Default

Today, I twisted the two halves of the melted green wire together and turned the ignition to ACC. Nothing happened, the green wire was unaffected. Then I started the engine. I got out and saw that the repair I had made in the green wires had melted. Something is happening when I start the engine that causes this fusible link to melt.
kenmack is offline   Reply With Quote
Old 04-26-2018, 06:46 PM   #6
metalincarnate
 
Join Date: Apr 2018
Location: NM
Posts: 1
Vehicle: D21 v6 4x4 1987
Thanks: 0
Thanked 0 Times in 0 Posts
Default

Hey whats up Kenmack, Im having the same problem. I traced the green fusible link which turns into a white/red wire.The w/r wire seems to split into a Y near the door panel, into two white/red wires that go into to ecu. I had continuity from the Y to the ecu, but not from the Y to the fusible link. Weird. So i put a jumper wire across , just outside the fusible link on the w/r wire down to the Y. It was starting before but the fusible link was getting hot, this somehow solved the problem. SO, I elimated that section of "uncontinuitied" wire out effectively by jumping the wire altogether. But now it wont start, seems like its not firing injectors and I also keep getting a tps error which never happened before. This W/R wire has got to be connected to something else? Did you ever solve your probleM?
metalincarnate is offline   Reply With Quote
Old 04-26-2018, 08:38 PM   #7
jp2code
Software Developer
 
jp2code's Avatar
 
Join Date: Dec 2011
Location: Longview, TX [USA]
Age: 48
Posts: 8,049
Vehicle: 94 LB 2x4 Manual VG33e
Thanks: 1,158
Thanked 998 Times in 875 Posts
Default

Check for error codes and see if the ECU is fried.

The diagram really isn't much help.

__________________
Joe (not a mechanic!) Don't have an account? EMAIL ME
Free Service Manuals: -
Walk-through: Checking Nissan Trouble Codes
Everyone you meet is fighting a battle you know nothing about. Be kind always.

jp2code is offline   Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT. The time now is 07:39 PM.


Powered by vBulletin® Version 3.8.6
Copyright ©2000 - 2018, Jelsoft Enterprises Ltd.