Go Back   Infamous Nissan - Hardbody / Frontier Forums > Tech Area > Wiring and Electrical

Reply
 
Thread Tools Display Modes
Old 04-27-2012, 09:12 PM   #1
dustinbleh
 
Join Date: Mar 2012
Location: Phoenix, AZ
Posts: 16
Vehicle: 1993 Nissan D21
Thanks: 0
Thanked 8 Times in 1 Post
Default HOW TO: Install Aftermarket Tachometer

So I know there is info on this scattered over the forum; bits and pieces here and there; but when I wanted to know how to do this I was unable to find a full write up. So, now that I know how to do this I figured I could write up how I did this in case anyone else wants to know.

Its really straight forward. For being my first install it only took me around an hour or so total to run the wires and hook everything up. The install location is totally up to you and kind of depends on what your tach comes with, but im sure you can figure that part out.

This applies to my 1993 D21 with a 2.4L engine and a 5 speed manual trans. Your vehicle may differ slightly or totally, so be sure to test the tach in the engine compartment before you run the wires and install the tach.

Here is the tach I will be installing:


I picked this up on craigslist for $10. Gotta love craigslist! It has 4 wires coming out of it:
Green: Tachometer lead
White: 12v Switched (Illumination lead)
Red: 12v Constant Positive
Black: Ground

Your Tach may be different. Read your manual!

This is where you will be tapping into the tach signal wire (directly off the ignition coil):


On my coil it is the BLUE wire coming from the plug on the bottom of the coil:


I used one of these type of electrical connectors to splice my own wire into the tach signal wire, as well as the power/illumination wires:


You can test the tach by connecting the signal wire to tach, and connecting the red and black wires to the battery and then starting the truck. The tach should be functioning.

Once you have your tach signal wire squared away and tested, you need to find a spot on the firewall to run your signal wire lead through:


For my install, I used the boot that the cable for the hood goes through. Mine was already ripped slightly so I ran the cable through that crack.

Now that the tach lead has been run to the cab of the truck and in/under the dash, you will want to run the other wires for your tachometer.

I removed the bezel around the ac/cigg lighter/ashtray and used power from under there to power my tach. Certain power sources may give interference so you may want to test everything before putting it all back together:


I connected the illumination (white) wire to the (+ Positive wire on the cigg lighter:


And then the Positive and Negative wires to the constant-on positive from the stereo and the ground from the stereo; but forgot to take a picture of this.. This is pretty straightforward though.

My tach came with one of these types of rounded mounts:


And rather than buying a new one, I took a hammer and flattened it out:


I am going to buy a proper mount when I find out where to permanently install the tach. In the meantime I ran a nut and bolt through the mounting hole for the tach and through the lefthand hole in the dash surround:


This works ok for now and the dash surround does still sit flat but it is not ideal because the gauge is'nt totally visible from behind the steering wheel:




So now you test the tach on the power sources you chose, and if everything is working properly you put everything back together!

I hope this helps someone with their installation. Obviously I did not do a perfect job or write up, but I think it gets the point across.. good luck!

dustinbleh is offline   Reply With Quote
Thanked by:
brnc_429 (07-15-2013), d21-92 (02-25-2013), d21trav (12-01-2015), DenverDude (01-05-2013), Drumahaulic (12-29-2014), Louis leclerc (12-06-2014), PeteJM (07-15-2013), sicnis (04-27-2012)
Old 04-27-2012, 10:19 PM   #2
minijdm95
1 JDM HARDBODY
 
minijdm95's Avatar
 
Join Date: Oct 2009
Location: SO-CAL
Posts: 313
Vehicle: 96/95 nissan pickup
Thanks: 8
Thanked 14 Times in 13 Posts
Default

great write up on this!
__________________
minijdm95 is offline   Reply With Quote
Old 04-27-2012, 10:50 PM   #3
dustinbleh
 
Join Date: Mar 2012
Location: Phoenix, AZ
Posts: 16
Vehicle: 1993 Nissan D21
Thanks: 0
Thanked 8 Times in 1 Post
Default

thanks! just trying to spread the knowledge.. i know i had to spend a while researching before i fully understood what to put where..

so hopefully this helps!
dustinbleh is offline   Reply With Quote
Old 05-16-2012, 06:00 AM   #4
Segundo
 
Segundo's Avatar
 
Join Date: Jan 2012
Location: Las Vegas, NV
Age: 29
Posts: 161
Vehicle: 1989 Nissan D21
Thanks: 6
Thanked 14 Times in 12 Posts
Default

Good write up!! It'll definitely come in handy one day!!
Segundo is offline   Reply With Quote
Old 08-27-2012, 08:17 PM   #5
OnAir88
how's it goin.
 
OnAir88's Avatar
 
Join Date: Jun 2011
Location: columbia, tennessee
Posts: 1,840
Vehicle: 1988 bagged hardbody
Thanks: 248
Thanked 171 Times in 158 Posts
Default

So I had a tach like that except all black. I used all different wires except for the blue wire that connects to the green. This really helped me out, did a good job.
__________________
I'm just trying to build something that stands out from the rest of society.
OnAir88 is offline   Reply With Quote
Old 01-05-2013, 12:26 AM   #6
rawbeetz
 
Join Date: Aug 2012
Location: Maui
Posts: 2
Vehicle: 87 nissan hardbody
Thanks: 0
Thanked 0 Times in 0 Posts
Default

Thanks man help alot!!!
rawbeetz is offline   Reply With Quote
Old 03-16-2013, 08:21 PM   #7
jcbenoit
 
jcbenoit's Avatar
 
Join Date: Feb 2013
Location: Ottawa, Ontario
Posts: 213
Vehicle: 1994 Nissan Hardbody 2.4L Automatic
Thanks: 81
Thanked 5 Times in 5 Posts
Default

I followed every steps and adjusted my gauge for a 4cyl but I'm not getting a good signal. The signal is around 4000 RPMs. How could I fix this?
Thanks
jcbenoit is offline   Reply With Quote
Old 04-06-2013, 09:17 PM   #8
SleepyReaper2.o
 
SleepyReaper2.o's Avatar
 
Join Date: Mar 2013
Location: Lima Oh
Posts: 15
Vehicle: 1997 Hardbody
Thanks: 0
Thanked 1 Time in 1 Post
Default

Will be using this! Thanks!
SleepyReaper2.o is offline   Reply With Quote
Old 06-21-2013, 12:18 AM   #9
cadillacdude1975
The Gear Jammer
 
cadillacdude1975's Avatar
 
Join Date: Apr 2013
Location: Chattanooga, TN
Age: 46
Posts: 8,471
Vehicle: 87 D21 SE KC V6 2wd 5sp & 86.5 V6 SE auto
Thanks: 300
Thanked 933 Times in 865 Posts
Default

it would be nice if there was an aftermarket tach that would fit inside the cluster where the factory junk was.
cadillacdude1975 is online now   Reply With Quote
Old 07-15-2013, 10:04 PM   #10
PeteJM
 
Join Date: Jul 2013
Location: Charleston, SC
Posts: 5
Vehicle: 91 D21 Hardbody
Thanks: 1
Thanked 0 Times in 0 Posts
Default

I will be using this as soon as I re-tap my distributor! :P
PeteJM is offline   Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT. The time now is 01:05 AM.


Powered by vBulletin® Version 3.8.6
Copyright ©2000 - 2018, Jelsoft Enterprises Ltd.