firearm friendly? - Page 122 - Infamous Nissan

89'HBV6 · 01-10-2022, 07:36 PM

OldGreyBeast · 01-10-2022, 09:37 PM

Man I've wanted to do a PM-63 build for a long time. The parts kits were nearly free for a good while (except barrels) but there is definitely not a whole lot of info out there on doing builds of them haha. Good luck on making it happen! I started an Uzi build a few weeks before I got sick, hoping to get back to that after I get the upstairs of my shop finished out. Trying to take advantage of the cooler temps to get all the harder labor out of the way.

Deerhurst · 01-11-2022, 01:26 AM

I am building.it up in solidworks. I have the FP and striker figured out for the most part. Will need some tweaking of course. Working in the stuff in the lower. Might have to turn my own barrel.

Going to use the resin printer to print a 1:1 to mock stuff up in and to mill before I screw up the real thing.

OldGreyBeast · 01-11-2022, 03:01 PM

Man I wish I was as good at that stuff. I need to get with you sometime to see if you can figure out a better trigger design for my PPSh. The TNW trigger is a solid 26lb (I kid you not). My efforts to reduce the pull have typically had results that are spicier than allowed.

Deerhurst · 01-11-2022, 05:42 PM

I like spicy triggers!

I used the factory trigger on my PPSh. Denials, welds, etc so semi only.

Sure, I'll help! Are you on weaponsguild?

OldGreyBeast · 01-11-2022, 09:28 PM

Haha I do too, I wish you could still register new MGs. I already have it stamped for being an SBR anyway, would just restore it back to full chooch if it was legal.

I wish TNW would have used the original trigger. Mine has some jerry rigged nonsense that looks like it was milled with a dremel in it lol. They built the Suomi I have and did a really good job with it but the PPSh is pretty horrible.

I've browsed weaponsguild a fair bit but don't have an account there. I should probably make one. I keep messing around thinking of ways to maybe 3d print up a prototype trigger but I'm not so good at the design phase with little small stuff like this.

Deerhurst · 01-12-2022, 02:54 AM

I'm under the same name there. I've got a thread for my PM63 build. I'll be posting CAD screen shots of trigger bar stuff later tonight.

This weekend I'll SLA print the frame and slide. Then a barrel. Then all the trigger bits.

Deerhurst · 01-12-2022, 03:57 AM

Deerhurst · 05-03-2022, 12:46 AM

PM-63 above is on hold until I get a barrel but I did build this! Got a few things to polish and the receiver weld need to be ground down and cleaned up but it runs!

cadillacdude1975 · 05-03-2022, 03:18 AM

Very nice.

01-10-2022, 09:37 PM	#1212
OldGreyBeast 1986.5 HB 4x4 3.0V6 Join Date: Mar 2012 Location: North AL Age: 34 Posts: 4,088 Vehicle: '86.5 Nissan D21, '87 Mercedes 190D Turbo, '10 Mercedes E350 AWD, '16 Suzuki GSXS1000 Thanks: 425 Thanked 540 Times in 464 Posts	Man I've wanted to do a PM-63 build for a long time. The parts kits were nearly free for a good while (except barrels) but there is definitely not a whole lot of info out there on doing builds of them haha. Good luck on making it happen! I started an Uzi build a few weeks before I got sick, hoping to get back to that after I get the upstairs of my shop finished out. Trying to take advantage of the cooler temps to get all the harder labor out of the way. __________________ Build log for the Beast - https://beastbuildlog.blogspot.com - Last Updated 8 MAR 2021 1986.5 FSM GI section - https://imgur.com/gallery/mjT18bV

01-11-2022, 01:26 AM	#1213
Deerhurst 4/86 SE-V6 2 tone 4x4 HB Join Date: Apr 2013 Location: Oregon Posts: 8,042 Vehicle: 1986.5 SE-V6 4WD D21, 2003 Audi A4 Avant 3.0 Quattro Thanks: 917 Thanked 1,080 Times in 976 Posts	I am building.it up in solidworks. I have the FP and striker figured out for the most part. Will need some tweaking of course. Working in the stuff in the lower. Might have to turn my own barrel. Going to use the resin printer to print a 1:1 to mock stuff up in and to mill before I screw up the real thing. __________________ 1986.5 SE-V6 4X4 D21 Hardbody Pacesetter Long Tube Headers Morimoto Mini D2S HID Projectors and Hella 500s VG33i

01-11-2022, 03:01 PM	#1214
OldGreyBeast 1986.5 HB 4x4 3.0V6 Join Date: Mar 2012 Location: North AL Age: 34 Posts: 4,088 Vehicle: '86.5 Nissan D21, '87 Mercedes 190D Turbo, '10 Mercedes E350 AWD, '16 Suzuki GSXS1000 Thanks: 425 Thanked 540 Times in 464 Posts	Man I wish I was as good at that stuff. I need to get with you sometime to see if you can figure out a better trigger design for my PPSh. The TNW trigger is a solid 26lb (I kid you not). My efforts to reduce the pull have typically had results that are spicier than allowed. __________________ Build log for the Beast - https://beastbuildlog.blogspot.com - Last Updated 8 MAR 2021 1986.5 FSM GI section - https://imgur.com/gallery/mjT18bV

01-11-2022, 05:42 PM	#1215
Deerhurst 4/86 SE-V6 2 tone 4x4 HB Join Date: Apr 2013 Location: Oregon Posts: 8,042 Vehicle: 1986.5 SE-V6 4WD D21, 2003 Audi A4 Avant 3.0 Quattro Thanks: 917 Thanked 1,080 Times in 976 Posts	I like spicy triggers! I used the factory trigger on my PPSh. Denials, welds, etc so semi only. Sure, I'll help! Are you on weaponsguild? __________________ 1986.5 SE-V6 4X4 D21 Hardbody Pacesetter Long Tube Headers Morimoto Mini D2S HID Projectors and Hella 500s VG33i

01-11-2022, 09:28 PM	#1216
OldGreyBeast 1986.5 HB 4x4 3.0V6 Join Date: Mar 2012 Location: North AL Age: 34 Posts: 4,088 Vehicle: '86.5 Nissan D21, '87 Mercedes 190D Turbo, '10 Mercedes E350 AWD, '16 Suzuki GSXS1000 Thanks: 425 Thanked 540 Times in 464 Posts	Haha I do too, I wish you could still register new MGs. I already have it stamped for being an SBR anyway, would just restore it back to full chooch if it was legal. I wish TNW would have used the original trigger. Mine has some jerry rigged nonsense that looks like it was milled with a dremel in it lol. They built the Suomi I have and did a really good job with it but the PPSh is pretty horrible. I've browsed weaponsguild a fair bit but don't have an account there. I should probably make one. I keep messing around thinking of ways to maybe 3d print up a prototype trigger but I'm not so good at the design phase with little small stuff like this. __________________ Build log for the Beast - https://beastbuildlog.blogspot.com - Last Updated 8 MAR 2021 1986.5 FSM GI section - https://imgur.com/gallery/mjT18bV

01-12-2022, 02:54 AM	#1217
Deerhurst 4/86 SE-V6 2 tone 4x4 HB Join Date: Apr 2013 Location: Oregon Posts: 8,042 Vehicle: 1986.5 SE-V6 4WD D21, 2003 Audi A4 Avant 3.0 Quattro Thanks: 917 Thanked 1,080 Times in 976 Posts	I'm under the same name there. I've got a thread for my PM63 build. I'll be posting CAD screen shots of trigger bar stuff later tonight. This weekend I'll SLA print the frame and slide. Then a barrel. Then all the trigger bits. __________________ 1986.5 SE-V6 4X4 D21 Hardbody Pacesetter Long Tube Headers Morimoto Mini D2S HID Projectors and Hella 500s VG33i

01-12-2022, 03:57 AM	#1218
Deerhurst 4/86 SE-V6 2 tone 4x4 HB Join Date: Apr 2013 Location: Oregon Posts: 8,042 Vehicle: 1986.5 SE-V6 4WD D21, 2003 Audi A4 Avant 3.0 Quattro Thanks: 917 Thanked 1,080 Times in 976 Posts	__________________ 1986.5 SE-V6 4X4 D21 Hardbody Pacesetter Long Tube Headers Morimoto Mini D2S HID Projectors and Hella 500s VG33i

05-03-2022, 12:46 AM	#1219
Deerhurst 4/86 SE-V6 2 tone 4x4 HB Join Date: Apr 2013 Location: Oregon Posts: 8,042 Vehicle: 1986.5 SE-V6 4WD D21, 2003 Audi A4 Avant 3.0 Quattro Thanks: 917 Thanked 1,080 Times in 976 Posts	PM-63 above is on hold until I get a barrel but I did build this! Got a few things to polish and the receiver weld need to be ground down and cleaned up but it runs! __________________ 1986.5 SE-V6 4X4 D21 Hardbody Pacesetter Long Tube Headers Morimoto Mini D2S HID Projectors and Hella 500s VG33i

05-03-2022, 03:18 AM	#1220
cadillacdude1975 The Gear Jammer Join Date: Apr 2013 Location: Chattanooga, TN Age: 50 Posts: 10,682 Vehicle: 87 VG33 Pathfinder SE 4x4 & 87 D21 SE Thanks: 457 Thanked 1,400 Times in 1,265 Posts	Very nice.

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode