Go Back   Infamous Nissan - Hardbody / Frontier Forums > Tech Area > Performance and Drifting

Reply
 
Thread Tools Display Modes
Old 11-15-2014, 01:37 AM   #1
CasanovaGDP
 
CasanovaGDP's Avatar
 
Join Date: Aug 2013
Location: Dallastown PA
Posts: 557
Vehicle: 86.5 Nissan Hardbody
Thanks: 49
Thanked 54 Times in 51 Posts
Default motor options

Im looking at getting some power out of my truck. I saw a few options on here and read the d21 vs s13 block thread and have a few questions.
I have the z24i. Im extremely familiar with turbo cars and motor swap wiring and hiccups( ive owned a conquest, turbo neon, plymouth laser, turbo mustang) so little things wont bother me
If I go ka24de route should I get one out of a frontier or will one from a 240 work or are those oil pans different as well? If I do grab the frontier can I use my trans? Or is it better to just drop a ka24e out of a hardbody and do the typical 240 intake swap and just low boost the motor? I read somewhere about someone taking the z block and adding the ka24e pistons and heads and a cam for a little more power? Anyone have a little more info on this?
CasanovaGDP is offline   Reply With Quote
Old 11-16-2014, 03:21 PM   #2
scoobysmak
Xtreme Lowz
 
scoobysmak's Avatar
 
Join Date: Jan 2011
Location: Southeast TN
Age: 44
Posts: 3,283
Vehicle: 90 KA24 2wd Std Cab, 91 SR20DET 2wd Ext Cab
Thanks: 334
Thanked 424 Times in 401 Posts
Default

I am in uncharted waters for me on this engine but think the z24i put out around 106 hp and the ka24e puts out about 134 hp, I think most of this was because the compression ratio on the z24 is lower but that is somewhat better because you can run more boost. I have not found any builds that turbo'd the z24 but I am sure it has happened.
__________________
The Kids= Down N Out: 91 Nissan Ext Cab, SR20DET, Build Thread: http://www.infamousnissan.com/forum/...ad.php?t=20041
The daily: 90 Nissan Std Cab, KA24, Build thread:http://www.infamousnissan.com/forum/...476#post413476

87 Nissan Pathfinder...on hold... , 93 Nissan Pickup Long Bed.....needs help!!!
scoobysmak is offline   Reply With Quote
Old 11-16-2014, 03:30 PM   #3
CasanovaGDP
 
CasanovaGDP's Avatar
 
Join Date: Aug 2013
Location: Dallastown PA
Posts: 557
Vehicle: 86.5 Nissan Hardbody
Thanks: 49
Thanked 54 Times in 51 Posts
Default

I really only want about 200-250 so Im thinking with a complete rebuild on the 24e motor with 240 intake. A cam and small turbo ( mitsu 16g) front mount and fuel system thats achievable
CasanovaGDP is offline   Reply With Quote
Old 03-06-2018, 04:53 PM   #4
Nissun
 
Join Date: Mar 2018
Location: Greensburg
Posts: 4
Vehicle: 1987 Nissan d21 hardbody convertible
Thanks: 0
Thanked 0 Times in 0 Posts
Default Question regarding this thread I realize itís four years old

Can you tell me what wiring harness you end up using I just purchased an engine that already had the 240 upgrade to the ka 24e and I also have an 87 the 24 I that Iím removing iíve also seen talk about needing to replace the instrument panel and of course you need the ECu can you confirm or deny any of these Thanks in advance
Nissun is offline   Reply With Quote
Old 03-06-2018, 08:39 PM   #5
91nissan94
 
91nissan94's Avatar
 
Join Date: Sep 2008
Location: Crescent City FL
Posts: 1,403
Vehicle: 91nissan hb
Thanks: 65
Thanked 138 Times in 126 Posts
Default

The truck harness with a little moving of wires works fine. What year motor do you have?The 240 swap will run on the truck ecu. If you use the 240 ecu your tach will not work.
91nissan94 is offline   Reply With Quote
Old 03-06-2018, 09:38 PM   #6
86.5KC
 
86.5KC's Avatar
 
Join Date: Jun 2016
Location: Lehigh Valley PA
Posts: 137
Vehicle: Nissan D21 1986.5, King Cab, Z24i, 5speed, 2wd
Thanks: 12
Thanked 46 Times in 44 Posts
Default

Hi Nissun,
I bought CasanovaGDP's truck back in 2016, The truck still has the Z24 engine so I can say that this swap never happened in this truck. I did have a donor 240 swap that fell through, so I never truly looked into making the KA24E work properly when swapped. The more I think about it, the more I am leaning toward swapping in a V8.... As far as your question goes I think you will want everything(harness and ecu) from the donor to make the swap go as smooth as possible. The truck trans should bolt to the engine, but that is as much as I know for sure.
86.5KC is offline   Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT. The time now is 02:56 PM.


Powered by vBulletin® Version 3.8.6
Copyright ©2000 - 2018, Jelsoft Enterprises Ltd.