![]() |
#11 |
Super Moderator
Join Date: Mar 2009
Location: Port Orchard, WA
Posts: 4,535
Vehicle: 96 HB
Thanks: 154
Thanked 597 Times in 527 Posts
|
![]()
today was a good day I think. almost finished the rear. just have to install the pass. coilover and the trackbar, test for binding and finish welding then.
![]() ![]() ![]() ![]() ![]() ![]() ![]()
__________________
|
![]() |
![]() |
![]() |
#12 |
Super Moderator
Join Date: Mar 2009
Location: Port Orchard, WA
Posts: 4,535
Vehicle: 96 HB
Thanks: 154
Thanked 597 Times in 527 Posts
|
![]()
so yesterday was another good day.
finished up the pass. side. ![]() and ripped out the front. ![]() ![]() time for more grinding.
__________________
|
![]() |
![]() |
![]() |
#13 |
Join Date: Sep 2008
Location: Springfield, Il
Posts: 1,161
Vehicle: Hb-less at the moment
Thanks: 5
Thanked 48 Times in 47 Posts
|
![]()
This is gonna be sweet. It's looking good already. What axle are you using for the front? Dana 44? Are you running a 4cyl or v6? Just curious, I'll be doing the same once my Yukon dies. I've read a little here and there about the sas, just ready to lift a hb! Keep it up.
__________________
Looking for a project extended cab again....
|
![]() |
![]() |
![]() |
#14 |
Super Moderator
Join Date: Mar 2009
Location: Port Orchard, WA
Posts: 4,535
Vehicle: 96 HB
Thanks: 154
Thanked 597 Times in 527 Posts
|
![]()
its a Dana 44 for the front, I'm running 5.13 gears and it has a 4 cyl. the gears will bring it back to the stock 4.63s.
ok, its OFFICIAL!! the IFS is officially GONE!!!!! ![]() ![]() and the rims I ordered came in today! ![]() and then mounted them. ![]() cut the Cs and turned them, that was a PITA, to what looked good, then place the axle under the truck for driveline angle. unfortunately the Cs need a little more coaxing. dang it. ![]() ![]() plan for tomorrow. install the 3-link and coilovers. have a rolling chasis by the end of the day!
__________________
|
![]() |
![]() |
![]() |
#15 |
INfamous Sentra Driver
Join Date: May 2009
Location: Apopka, Florida
Age: 35
Posts: 384
Vehicle: 1994 Nissan Sentra Sedan
Thanks: 0
Thanked 0 Times in 0 Posts
|
![]()
Damn lookin good brother keep up the pace!
__________________
"Heart of a Ricer,Soul of Mintrucker" My Ride- 1994 Nissan Sentra Sedan- Stock for nowThe Wifey's- 1999 Nissan Altima GXE- Getting girlyfied ![]() |
![]() |
![]() |
![]() |
#16 |
Join Date: Mar 2009
Location: washington
Posts: 715
Vehicle: 2006 nissan titan
Thanks: 0
Thanked 2 Times in 2 Posts
|
![]()
go big!!!!
|
![]() |
![]() |
![]() |
#17 |
Washed off the dirt!!
Join Date: Sep 2008
Location: se ga
Posts: 1,114
Vehicle: 1985 720,1985 720,2000 silverado
Thanks: 26
Thanked 4 Times in 4 Posts
|
![]()
Gonna be bad!!!!!!
__________________
A minitrucker looks at forty.......
|
![]() |
![]() |
![]() |
#18 |
Super Moderator
Join Date: Mar 2009
Location: Port Orchard, WA
Posts: 4,535
Vehicle: 96 HB
Thanks: 154
Thanked 597 Times in 527 Posts
|
![]()
well, not the progress I wanted but it was forward.
![]() ![]() ![]() ![]() I did get the Cs done, they were complete PITAs, but the BFH showed them who the boss was.
__________________
|
![]() |
![]() |
![]() |
#19 |
mod
Join Date: Sep 2008
Location: carriere, ms
Age: 31
Posts: 2,808
Vehicle: 98 frontier
Thanks: 52
Thanked 97 Times in 88 Posts
|
![]()
haha BFH always wins. lookin nice man
__________________
aaron
|
![]() |
![]() |
![]() |
#20 |
Super Moderator
Join Date: Mar 2009
Location: Port Orchard, WA
Posts: 4,535
Vehicle: 96 HB
Thanks: 154
Thanked 597 Times in 527 Posts
|
![]()
IT'S ON ALL 4 WHEELS!!!
![]() It's a beautiful site for sure. still need to figure out how I want to do the upper link for the front though. its kinda set up like a jeep at the moment with upper link tied to the lower to hold the pinion angle. I'm not really wanting to do that. I was hoping there was room on the pass. side, but its only like 2" and under flex the tube would hit the oil pan. not sure if I want to do the dr. side because I would have to totally refab the tranny x-member. I was only wanting to put a hoop in it for the frt d/line. still needs brakes, steering, frt trackbar, place a tube from hoop to hoop on the frt (over the engine) for support and I want to redo the rear trackbar. so without any further ado, here are the latest pics... ![]() ![]() ![]() ![]() ![]() ![]()
__________________
|
![]() |
![]() |
![]() |
Thread Tools | |
Display Modes | |
|
|