Go Back   Infamous Nissan - Hardbody / Frontier Forums > Commerce > Vendors

Reply
 
Thread Tools Display Modes
Old 08-04-2011, 06:14 PM   #1
beebani
Approved Vendor
 
beebani's Avatar
 
Join Date: Oct 2008
Location: Independence, Oregon
Posts: 394
Vehicle: 1976 Datsun 620
Thanks: 11
Thanked 27 Times in 24 Posts
Default rear disc brake brackets

Parts Needed:

Rear
Rotors, calipers, pads, and lines: 1989-1993 Isuzu amigo, 1988-1991 Isuzu Trooper, 1988-1995 Isuzu Pickup


Instructions:


Rear:
1. Remove Wheels
2. Remove drums
3. Remove parking brake cables
4. Remove brake lines from wheel cylinders
5. Remove 4 nuts behind backing plate assembly
6. Remove axle assembly (be sure to keep track of preload shims)
7. Remove the 4 studs (be sure no to damage the threads as you are going to re-use these)
8. The backing plate should be able to slide off the bearing housing to give you a better angle at your next step.
9. Remove backing plate. You have two ways of doing this. You can either have a machine shop remove the bearing assembly the “book” way or you can cut the backing plate off. If you choose the later be sure to protect the bearing assembly from the metal shavings you will create during the procedure.
10. Install the studs back in the bearing housing
11. Install axle back into axle tube with bearing spacer shims
12. Place caliper mounting bracket on the back side of the axle tube with the caliper position toward the rear of the vehicle and replace nuts removed in step 5
13. Slide rotor over axle
14. Install caliper mounting bracket using supplied spacers
15. Install calipers and pads
16. Install Isuzu rubber brake lines with banjo bolts and connect other end to existing hard lines



Resized to 66% (was 1023 x 680) - Click image to enlarge





Resized to 66% (was 1024 x 766) - Click image to enlarge



Resized to 66% (was 1024 x 766) - Click image to enlarge




These come with the caliper mounting hardware, and they are painted. The set sells for $150 shipped in the US.

The stock e-brake cable will have to be lengthened, but these calipers do have a built in e-brake lever.


These will work on all H190 axles, been making these for Datsuns for years, and have just figured out what it will take for them to work on the hardbodies, just had to lengthen the spacers.


I will be working on a vented dual piston setup for the rear soon.

Last edited by beebani; 04-13-2012 at 04:54 PM. Reason: updated new price
beebani is offline   Reply With Quote
Thanked by:
cstmimg (10-24-2012), ogskeeta (08-10-2014)
Old 08-04-2011, 06:22 PM   #2
pugz
//NC\\ Admin ex-owner
 
pugz's Avatar
 
Join Date: Sep 2008
Location: Spring, TX
Age: 38
Posts: 9,632
Vehicle: Honda part sales
Thanks: 263
Thanked 185 Times in 144 Posts
Default

Does this space out the rear wheels??
__________________
www.photosbypugz.com www.facebook.com/photosbypugz
MiniTruckin Magazine Photographer
pugz is offline   Reply With Quote
Old 08-04-2011, 06:23 PM   #3
RedAggie03
Super Moderator
 
RedAggie03's Avatar
 
Join Date: Oct 2010
Location: Houston, TX
Age: 37
Posts: 2,408
Vehicle: 1992 Nissan D21 Extended Cab
Thanks: 33
Thanked 165 Times in 140 Posts
Default

Nice! I am concerned about the "extend the e-brake cable" part though. How would you do that? Does that require a custom cable?

^^^^ oh that's a good question too Pugz. It would be uber pimp if it brought the rear wheels IN just a touch.
RedAggie03 is offline   Reply With Quote
Old 08-04-2011, 06:30 PM   #4
beebani
Approved Vendor
 
beebani's Avatar
 
Join Date: Oct 2008
Location: Independence, Oregon
Posts: 394
Vehicle: 1976 Datsun 620
Thanks: 11
Thanked 27 Times in 24 Posts
Default

The wheels will virtually be in the same location as the drum is the same thickness as the rotor hat.

The ebrake cable extension is necessary on the Datsuns, but not 100% sure on the 720/hardbody. It is a simple fix though, some cable and clamps or crimp fittings from any hardware store will do the trick. I will post some pics of the upgrade.
beebani is offline   Reply With Quote
Old 08-04-2011, 06:34 PM   #5
pugz
//NC\\ Admin ex-owner
 
pugz's Avatar
 
Join Date: Sep 2008
Location: Spring, TX
Age: 38
Posts: 9,632
Vehicle: Honda part sales
Thanks: 263
Thanked 185 Times in 144 Posts
Default

I might need a set of these for the pathy build
__________________
www.photosbypugz.com www.facebook.com/photosbypugz
MiniTruckin Magazine Photographer
pugz is offline   Reply With Quote
Thanked by:
91nissan94 (05-29-2017)
Old 08-06-2011, 02:40 PM   #6
98frontier
Brandon "bSol" Solomon
 
98frontier's Avatar
 
Join Date: Sep 2008
Location: Dillsburg, Pa
Age: 40
Posts: 618
Thanks: 0
Thanked 4 Times in 4 Posts
Default

Quote:
Originally Posted by pugz View Post
I might need a set of these for the pathy build
That's mandatory!
__________________
http://www.infamousnissan.com/forum/image.php?type=sigpic&userid=228&dateline=12603151  64
98frontier is offline   Reply With Quote
Old 08-07-2011, 04:02 AM   #7
4DRZ
 
4DRZ's Avatar
 
Join Date: Mar 2011
Location: Florida
Posts: 509
Vehicle: 2000 Nissan Frontier ext. cab
Thanks: 29
Thanked 19 Times in 19 Posts
Default

Does this also work on the 1st gen Frontier? Would love to do this! lol
4DRZ is offline   Reply With Quote
Old 08-07-2011, 07:17 AM   #8
beebani
Approved Vendor
 
beebani's Avatar
 
Join Date: Oct 2008
Location: Independence, Oregon
Posts: 394
Vehicle: 1976 Datsun 620
Thanks: 11
Thanked 27 Times in 24 Posts
Default

Quote:
Originally Posted by 4DRZ View Post
Does this also work on the 1st gen Frontier? Would love to do this! lol
if it has the H190 axle, it should
beebani is offline   Reply With Quote
Old 08-07-2011, 03:38 PM   #9
4DRZ
 
4DRZ's Avatar
 
Join Date: Mar 2011
Location: Florida
Posts: 509
Vehicle: 2000 Nissan Frontier ext. cab
Thanks: 29
Thanked 19 Times in 19 Posts
Default

Sorry for the newb questions, but how will I know if it does or doesnt?
4DRZ is offline   Reply With Quote
Old 08-07-2011, 03:53 PM   #10
beebani
Approved Vendor
 
beebani's Avatar
 
Join Date: Oct 2008
Location: Independence, Oregon
Posts: 394
Vehicle: 1976 Datsun 620
Thanks: 11
Thanked 27 Times in 24 Posts
Default

I just did a little research, and it looks like the frontiers used all the same rear brake parts as the hb up through 2003, '04-'05 is when they went with discs in the rear.
beebani is offline   Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT. The time now is 11:26 AM.


Powered by vBulletin® Version 3.8.6
Copyright ©2000 - 2018, Jelsoft Enterprises Ltd.