Go Back   Infamous Nissan - Hardbody / Frontier Forums > Model Specific > Hardbody Forum (D21)

Reply
 
Thread Tools Display Modes
Old 03-03-2014, 12:37 PM   #11
cadillacdude1975
The Gear Jammer
 
cadillacdude1975's Avatar
 
Join Date: Apr 2013
Location: Chattanooga, TN
Age: 45
Posts: 7,670
Vehicle: 87 D21 SE KC V6 2wd 5sp & 86.5 V6 SE auto
Thanks: 253
Thanked 816 Times in 759 Posts
Default

yes. its listed at the top of the page for the selected year make and model. there are more, i just got busy yesterday and didnt have time to play on the interwebs.

can a MOD fix the title for me? seems that i omitted the "T" from past lol
__________________
"Im officially lost" - wildbill

Last edited by cadillacdude1975; 03-03-2014 at 12:44 PM.
cadillacdude1975 is offline   Reply With Quote
Old 03-03-2014, 12:47 PM   #12
cadillacdude1975
The Gear Jammer
 
cadillacdude1975's Avatar
 
Join Date: Apr 2013
Location: Chattanooga, TN
Age: 45
Posts: 7,670
Vehicle: 87 D21 SE KC V6 2wd 5sp & 86.5 V6 SE auto
Thanks: 253
Thanked 816 Times in 759 Posts
Default

for the 94 models.......................

  • Recall - Seat Belt Buckle Replacement

Reference:
NTB02-055a Date:
December 11, 2002 VOLUNTARY RECALL CAMPAIGN FRONT SEAT BELT BUCKLE REPLACEMENT
IMPORTANT ^ This bulletin supercedes Recall Campaign bulletin NTB02-055 ^ Refer to this bulletin NTB02-055a for complete information ^ Please discard all previous copies of NTB02-055 ^ The seat belt buckle "lot code" range has been expanded CAMPAIGN I.D. # / NHTSA #: R2017/02V-125
APPLIED VEHICLE:
1994 Truck (D21) APPLIED VIN:
1N6*D1***RC300437 - 1N6*D1***RC390867 NOTE: Use Service Comm to confirm campaign eligibility. INTRODUCTION
The front seat belt buckles may contain a part that could cause the seat belt tongue not to fully engage if it is not firmly inserted into the buckle, and may result in the seat belt becoming unfastened in the event of a collision or hard braking. This problem only affects certain lot numbers of buckles as described in the SERVICE PROCEDURE section of this bulletin. Please note that the center seat belt buckle, in bench seat equipped D21 trucks, is not affected by this campaign.
IDENTIFICATION NUMBER
Nissan has assigned PNC R2017 to this campaign. This number must appear on all communications and documentation of any nature dealing with this campaign.
NUMBER OF VEHICLES POTENTIALLY AFFECTED
The number of vehicles potentially affected is approximately 71,000.
DEALER RESPONSIBILITY
It is the dealer's responsibility to check each vehicle falling within the range of this campaign which for any reason enters the service department. This includes vehicles purchased from private parties or presented by transient (tourist) owners and vehicles in dealer inventory. Federal law requires that new vehicles in dealer inventory which are the subject of a safety recall must be corrected prior to sale. Failure to do so can result in civil penalties by the National Highway Traffic Safety Administration. While the Federal law applies only to new cars, Nissan strongly encourages dealers to correct any affected used cars in their inventory before selling them.
OWNER NOTIFICATION
Owners of affected vehicles will be notified by mail requesting them to bring their vehicle in for front seat belt buckle inspection and replacement of any buckles with the affected lot numbers. A copy of this notification can be found on page 5/5 of this bulletin.
__________________
"Im officially lost" - wildbill
cadillacdude1975 is offline   Reply With Quote
Old 03-03-2014, 12:48 PM   #13
cadillacdude1975
The Gear Jammer
 
cadillacdude1975's Avatar
 
Join Date: Apr 2013
Location: Chattanooga, TN
Age: 45
Posts: 7,670
Vehicle: 87 D21 SE KC V6 2wd 5sp & 86.5 V6 SE auto
Thanks: 253
Thanked 816 Times in 759 Posts
Default

  • Recall 02V125000: Seat Belt Buckle Defect

DEFECT: On some trucks, the seat belt buckle latch plate was not manufactured according to design dimensions. If the seat belt tongue is inserted slowly at an angle into the buckle, there is a possibility of partial engagement. This condition can cause the seat belt tongue to come out of the buckle in the event of a collision or hard braking of the vehicle, increasing the risk of personal injury to an occupant of the seat.
Remedy: Dealers will inspect the buckle and, if necessary, replace the buckle assembly with a new buckle. The manufacturer has reported that owner notification began May 28, 2002. Owners who do not receive the free remedy within a reasonable time should contact Nissan at 1-800-647-7261.
__________________
"Im officially lost" - wildbill
cadillacdude1975 is offline   Reply With Quote
Old 03-03-2014, 12:48 PM   #14
cadillacdude1975
The Gear Jammer
 
cadillacdude1975's Avatar
 
Join Date: Apr 2013
Location: Chattanooga, TN
Age: 45
Posts: 7,670
Vehicle: 87 D21 SE KC V6 2wd 5sp & 86.5 V6 SE auto
Thanks: 253
Thanked 816 Times in 759 Posts
Default

  • Recall 96V170001: Seat Belt Buckle Defect

The latch plate used in the seat belt buckle was not manufactured according to design dimensions. If the seat belt tongue is inserted slowly at an angle into the buckle, there is a possibility of partial engagement. This condition can cause the seat belt tongue to come out of the buckle in the event of a collision or hard braking of the vehicle increasing the risk of personal injury to an occupant of the seat. Dealers will inspect the buckle and, if necessary, replace the buckle assembly with a new buckle. Owner Notification: Owner notification is expected to begin during November 1996.
NOTE: Owners who take their vehicles to an authorized dealer on an agreed upon service date and do not receive the free remedy within a reasonable time should contact Nissan at 1-800-647-7261. Also contact the National Highway Traffic Safety Administration's Auto Safety Hotline at 1-800-424-9393.
1994 NISSAN TRUCK D21
1994 NISSAN TRUCK PATHFINDER
__________________
"Im officially lost" - wildbill
cadillacdude1975 is offline   Reply With Quote
Old 03-03-2014, 12:49 PM   #15
cadillacdude1975
The Gear Jammer
 
cadillacdude1975's Avatar
 
Join Date: Apr 2013
Location: Chattanooga, TN
Age: 45
Posts: 7,670
Vehicle: 87 D21 SE KC V6 2wd 5sp & 86.5 V6 SE auto
Thanks: 253
Thanked 816 Times in 759 Posts
Default

for the 93 models................

  • Recall - Missing Hose Routing Label (Federal)

Classification:
BF92-026 Section:
Body & Frame Reference:
SERVICE BULLETIN NTB92-081/U9042 Models:
1992-93 Truck & 300ZX Date:
September 22, 1992 VOLUNTARY SERVICE CAMPAIGN: TRUCK (D21) AND 300ZX (Z32) VACUUM HOSE ROUTING LABEL
INTRODUCTION
Some 1992 and 1993 Trucks (D21) and 300ZX's may not have a Vacuum Hose Routing Label installed under the hood. The affected years and models are listed. All owners of the affected vehicles will receive a letter and new label, along with instructions for application. In the event assistance is needed, the owners will be instructed to contact their Nissan dealer for label application at no charge. A copy of the owner letter is shown in this Bulletin.
AFFECTED VEHICLES:
All 1992 Federal model Trucks (D21)
All 1993 Federal model Trucks (D21) up to Serial # 310237
All 1992 Federal model 300ZX's (Z32)
All 1993 Federal model 300ZX's (Z32) up to Serial # 530329 This campaign does not affect the Pathfinder (WD21) or any California specification models.
IDENTIFICATION NUMBER
Nissan has assigned identification number U9042 to this campaign. This number must appear on all communications and documentation of any nature dealing with this campaign.
__________________
"Im officially lost" - wildbill
cadillacdude1975 is offline   Reply With Quote
Old 03-03-2014, 12:50 PM   #16
cadillacdude1975
The Gear Jammer
 
cadillacdude1975's Avatar
 
Join Date: Apr 2013
Location: Chattanooga, TN
Age: 45
Posts: 7,670
Vehicle: 87 D21 SE KC V6 2wd 5sp & 86.5 V6 SE auto
Thanks: 253
Thanked 816 Times in 759 Posts
Default

for the 92 model..........

  • Recall - Missing Hose Routing Label (Federal)

Classification:
BF92-026 Section:
Body & Frame Reference:
SERVICE BULLETIN NTB92-081/U9042 Models:
1992-93 Truck & 300ZX Date:
September 22, 1992 VOLUNTARY SERVICE CAMPAIGN: TRUCK (D21) AND 300ZX (Z32) VACUUM HOSE ROUTING LABEL
INTRODUCTION
Some 1992 and 1993 Trucks (D21) and 300ZX's may not have a Vacuum Hose Routing Label installed under the hood. The affected years and models are listed. All owners of the affected vehicles will receive a letter and new label, along with instructions for application. In the event assistance is needed, the owners will be instructed to contact their Nissan dealer for label application at no charge. A copy of the owner letter is shown in this Bulletin.
AFFECTED VEHICLES:
All 1992 Federal model Trucks (D21)
All 1993 Federal model Trucks (D21) up to Serial # 310237
All 1992 Federal model 300ZX's (Z32)
All 1993 Federal model 300ZX's (Z32) up to Serial # 530329 This campaign does not affect the Pathfinder (WD21) or any California specification models.
IDENTIFICATION NUMBER
Nissan has assigned identification number U9042 to this campaign. This number must appear on all communications and documentation of any nature dealing with this campaign.
__________________
"Im officially lost" - wildbill
cadillacdude1975 is offline   Reply With Quote
Old 03-03-2014, 12:51 PM   #17
cadillacdude1975
The Gear Jammer
 
cadillacdude1975's Avatar
 
Join Date: Apr 2013
Location: Chattanooga, TN
Age: 45
Posts: 7,670
Vehicle: 87 D21 SE KC V6 2wd 5sp & 86.5 V6 SE auto
Thanks: 253
Thanked 816 Times in 759 Posts
Default

for the 91 models................

  • Recall 95V103002: Safety Belt Buckle Release Button

The front safety belt buckle release buttons can break. These red plastic release buttons are marked "press." If a button breaks, pieces can fall into the buckle assembly causing the buckle to operate improperly. The safety belts would not provide adequate protection to an occupant in a vehicle crash.
Owners should promptly check the condition and operation of both front safety belt buckles and carefully inspect the red release button for any breaks or cracks. They should ensure that both buckles are operating properly by inserting each latch plate into its buckle, tugging on the belt to make sure the latch is securely locked, and then pressing the release button. The latch plate should pop out of the buckle when the button is pressed. If either release button shows a sign of breaking or cracking or if either buckle fails to operate properly, owners should promptly contact their authorized dealer to schedule an appointment to have the buckle replaced or repaired free of charge.
System: Interior; Seat Belts; Belt Buckles.
Vehicle Description: Passenger, Multi-Purpose Vehicles and Light Duty Trucks Equipped with Safety Belts made by Takata Corporation.
NOTE: If your vehicle is presented to an authorized dealer on an agreed upon service date and the remedy is not provided free of charge within a reasonable time, please contact NISSAN at 1-800-647-7261. Also contact the National Highway Traffic Safety Administration's Auto Safety Hotline at 1-800-424-9393.
__________________
"Im officially lost" - wildbill
cadillacdude1975 is offline   Reply With Quote
Old 03-03-2014, 12:52 PM   #18
cadillacdude1975
The Gear Jammer
 
cadillacdude1975's Avatar
 
Join Date: Apr 2013
Location: Chattanooga, TN
Age: 45
Posts: 7,670
Vehicle: 87 D21 SE KC V6 2wd 5sp & 86.5 V6 SE auto
Thanks: 253
Thanked 816 Times in 759 Posts
Default

  • Recall - Front Seat Belt Buckles

Classification: 95V-103
Reference: NTB95-085a
Date: September 22, 1995
VOLUNTARY CAMPAIGN - FRONT SEAT BELT BUCKLES
This bulletin replaces NTB95-085.
Please discard all copies of NTB95-085, dated August 28, 1995. CAMPAIGN IDENTIFICATION NO.: 95V-103.002
APPLIED VEHICLES BELT TYPE 200SX (512) 1986.5-88 3 Point active lap/shoulder belt 240SX (S13) 1989-91 2 Point manual lap belt Truck (D21) 1988-91 3 Point active lap/shoulder belt (except center belt position) Pathfinder (WD21) 1988-91 3 Point active lap/shoulder belt Van (C22) 1987-90 3 Point active lap/shoulder belt Sentra (B12) 1987-90 3 Point active lap/shoulder belt & 2 Point manual lap belt Sentra (B13) 2 Door Sedan 19913 Point passive lap/shoulder belt (door mounted) AUTHORIZATION
Nissan Motor Co., Ltd. authorizes Nissan Motor Corporation., U.S.A. (NMC) to conduct a campaign on certain 1986.5-1991 Nissan vehicles.
INTRODUCTION
The National Highway Traffic Safety Administration (NHTSA) has been investigating certain seat belt buckles manufactured by Takata Corporation for vehicle model years 1986.5 through 1990 and a part of 1991. These buckles were installed in numerous models built by several manufacturers including certain 1986.5-91 Nissan and Infiniti models. Nissan is aware of a small number of reports of seat belt buckle release button breakage in vehicles equipped with these Takata buckles. A broken piece may prevent the buckle from latching or prevent it from unlatching.
NUMBER OF VEHICLES POTENTIALLY AFFECTED: Approximately 2,000,000.
DEALER RESPONSIBILITY
It is the dealer's responsibility to check each vehicle within the range of this campaign which for any reason enters the service department. This includes vehicles purchased from private parties or presented by transient (tourist) owners and vehicles in dealer inventory.
WARRANTY EXTENSION
Owners of 1986.5 through 1988 vehicles affected by this campaign have been given a lifetime limited warranty on the entire seat belt assemblies in their car. This lifetime limited warranty is the same as applied to 1989 and later Nissan vehicles.
__________________
"Im officially lost" - wildbill
cadillacdude1975 is offline   Reply With Quote
Old 03-03-2014, 12:52 PM   #19
cadillacdude1975
The Gear Jammer
 
cadillacdude1975's Avatar
 
Join Date: Apr 2013
Location: Chattanooga, TN
Age: 45
Posts: 7,670
Vehicle: 87 D21 SE KC V6 2wd 5sp & 86.5 V6 SE auto
Thanks: 253
Thanked 816 Times in 759 Posts
Default

  • Recall - Front Seat Belt Buckles Update

Reference:
NTB95-111 Date:
November 7, 1995 VOLUNTARY CAMPAIGN UPDATE
FRONT SEAT BELT BUCKLES This bulletin provides supplemental information to NTB95-085a dated September 22, 1995.
CAMPAIGN IDENTIFICATION NO:
95V-103.002 APPLIED VEHICLES:
200SX (S12) 1986.5-88 3 Point active lap/shoulder belt 24OSX (S13) 1989-91* 2 Point manual lap belt Truck (D21) 1988-91* 3 Point active lap/shoulder belt (except center belt position) Pathfinder (WD21) 1988-91* 3 Point active lap/shoulder belt Van (C22) 1987-90 3 Point active lap/shoulder belt Sentra (B12) 1987-90 3 Point active lap/shoulder belt & 2 Point manual lap belt Sentra (B13) 2 Door Sedan 1991* 3 Point passive lap/shoulder belt (door mounted) * See VIN Information in this bulletin for the ending serial numbers for 1991 models.
ADDITIONAL AND AMENDED INFORMATION
This bulletin contains information regarding the following:
^ Additional campaign background information ^ SERVICE-COMM information ^ Service Procedure: - Button replacement tips - Switch removal and installation ^ Vehicle specific information, VIN information for 1986.5 and 1991 models ^ 1987-1989 vehicle and warranty claims information ^ Parts Information: - Color mix by model. ADDITIONAL CAMPAIGN BACKGROUND INFORMATION
Industry wide, the Takata Seat Belt Campaign affects approximately 10,000,000 vehicles produced by most of the Japanese auto manufacturers. Nissan's share is about 2,000,000 cars and trucks.
All companies conducting the campaign are using a button replacement or buckle modification as the primary repair, with buckle replacement only as necessary. This strategy has been employed to expedite completion of the campaign because of the limited availability of Takata supplied replacement buckle assemblies. If this campaign were to require a 100% buckle assembly replacement, it would take two to three times as long to complete, which could lead to a great deal of customer dissatisfaction.
For this reason, dealers must follow the campaign procedure as described in NTB95-085a, and replace only the button on all vehicles unless replacement of the buckles is necessary.
SERVICE-COMM INFORMATION
Vehicles are being flagged in SERVICE-COMM as owner notifications are mailed. This enables both dealer and NMC personnel to quickly determine which owners have been mailed a notification. Please refer to the "applied vehicles" section of this bulletin to determine the complete affected vehicle population.
SERVICE PROCEDURE
Button Replacement Tips
The buckle assembly should be replaced only when one of the following conditions is observed:
^ Improper latching or unlatching ^ Buckle mechanism is contaminated with sticky material such as soft drink or juice ^ Foreign material is stuck in the buckle mechanism ^ The seat belt warning system switch is damaged. Switch Removal and Installation
Reference Campaign Bulletin NTB95-085a
Removal: step 5.
On buckles with the white plastic ejector mechanism, care should be taken when removing the buckle housing from the mechanism. The plastic spring locator and/or the springs can easily disengage and become loose causing the mechanism to bind when reassembled.
Removal; steps 6 & 7.
Use the recommended cutters and cut the three locating pins flush with the switch. Using a small flat bladed screwdriver, gently pry up on the switch at the lower portion near the locating pin. Repeat this at the upper pins. If the pins are cut correctly, the switch will come out with very little effort.
Installation; steps 18-20.
Follow the procedure in Step 18 exactly. Apply pressure with your thumb or a very small screwdriver only to the upper corners of the switch. Proper installation does not require that you hear a "click". The switch needs only to be over the locating pins and flush with the buckle cover.
Before installing the lower buckle cover (Step 19), the switch must be in the upward position. Failure to place the switch in this position will damage it. You must also depress the release button (Step 20) when snapping the cover in place. All of the above is clearly illustrated in the video tape shipped with Campaign Bulletin NTB95-085a.
VEHICLE SPECIFIC INFORMATION
VIN Information for 1986.5 models
Model Serial Number Range 200SX vehicles between 010051-121424 VIN Information for 1991 Models
Not all 1991 vehicles are affected by this campaign. The following are the ending serial numbers for the 1991 model vehicles affected by this campaign:
Model Ending Serial Number 240SX - Coupe 006837 240SX - Hatchback 023837 Pathfinder 032716 Truck - Japan production 412972 Truck - U.S. production 365000 Sentra 764000 1987-1989 Vehicle Torque Specifications
Reference Campaign Bulletin NTB95-085a
Sentra (1987-89, except 1989 Coupe)
Seat belt torque 18-23 ft-lbs (25-31 Nm, 2.5-3.2 kg-m) Buckle mounting bolt torque 26-34 ft lbs (35.8-45.6 Nm, 3.7-4.7 kg-m)
__________________
"Im officially lost" - wildbill
cadillacdude1975 is offline   Reply With Quote
Old 03-03-2014, 12:53 PM   #20
cadillacdude1975
The Gear Jammer
 
cadillacdude1975's Avatar
 
Join Date: Apr 2013
Location: Chattanooga, TN
Age: 45
Posts: 7,670
Vehicle: 87 D21 SE KC V6 2wd 5sp & 86.5 V6 SE auto
Thanks: 253
Thanked 816 Times in 759 Posts
Default

  • Recall - Front Seat Belt Buckles Addendum

Classification:
95V-103.002 Reference:
NTB96-020 Date:
February 7, 1996 VOLUNTARY CAMPAIGN UPDATE - FRONT SEAT BELT BUCKLES
APPLIED VEHICLES: BELT TYPE 200SX (S12) 1986.5-88 3 Point active lap/shoulder belt 240SX (S13) 1989-91 2 Point manual lap belt Truck (D21) 1988-91 3 Point active lap/shoulder belt (Except Center Belt Position) Pathfinder (WD21) 1988-91 3 Point active lap/shoulder belt Van (C22) 1987-90 3 Point active lap/shoulder belt Sentra (B12) 1987-90 3 Point active lap/shoulder belt & 2 point manual lap belt Sentra (B13) 2 Door Sedan 3 Point passive lap/shoulder belt 1991 (door mounted) SERVICE INFORMATION
This bulletin provides supplemental button kit information. Refer to NTB95-085a, dated September 22, 1995, for complete service and claims information.
__________________
"Im officially lost" - wildbill
cadillacdude1975 is offline   Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT. The time now is 12:36 PM.


Powered by vBulletin® Version 3.8.6
Copyright ©2000 - 2017, Jelsoft Enterprises Ltd.