Go Back   Infamous Nissan - Hardbody / Frontier Forums > Model Specific > Hardbody Forum (D21)

Reply
 
Thread Tools Display Modes
Old 06-21-2013, 01:44 AM   #81
sicnis
 
sicnis's Avatar
 
Join Date: Nov 2010
Location: SanAntonio Tx
Age: 34
Posts: 1,483
Vehicle: 1993 D21 Reg. Cab
Thanks: 164
Thanked 149 Times in 138 Posts
Default

main issue is having your pads correctly/safely contact your rotors, if you got the skills or money titan breaks could be done
doing the v6 hb upgrade is the cheapest easiest way, if i did it again i would have talked to beebani
__________________
sicnis is offline   Reply With Quote
Old 06-21-2013, 04:16 AM   #82
sparky
 
Join Date: Dec 2012
Location: Abilene, TX (Dyess AFB)
Posts: 135
Vehicle: 1997 Nissan Hardbody
Thanks: 0
Thanked 19 Times in 16 Posts
Default

Quote:
Originally Posted by TKisner View Post
I've had people tell me that Titan rotors will bolt right on the front. Can anyone confirm or deny this? If it is not the case what exactly is the issue?

The Titan rotors don't bolt up at all... not even close. the rotors use a 6 x 139.7 (6x5.5) bolt circle where the D21 uses a 6 x 103 bolt circle using the hub to get to the standard 6 x 139.7.
This is a pretty cool site to check the rotor sizes... http://www.centricparts.com/
sparky is offline   Reply With Quote
Old 09-10-2013, 01:01 AM   #83
dragnaz
 
dragnaz's Avatar
 
Join Date: Mar 2012
Location: Prescott Valley, AZ
Posts: 42
Vehicle: 86 1/2 Nissan Hardbody
Thanks: 3
Thanked 7 Times in 7 Posts
Default

Has anyone done a caliper swap after doing a toyota rotor/hub 5 lug swap?
dragnaz is offline   Reply With Quote
Old 01-15-2014, 10:15 PM   #84
kinglame
 
kinglame's Avatar
 
Join Date: Aug 2013
Location: california
Posts: 78
Vehicle: 1993 Hardbody (Ka24e)
Thanks: 7
Thanked 4 Times in 4 Posts
Default

can i still run my 14 inch rims up front if i do this
kinglame is offline   Reply With Quote
Old 01-15-2014, 10:32 PM   #85
cadillacdude1975
The Gear Jammer
 
cadillacdude1975's Avatar
 
Join Date: Apr 2013
Location: Chattanooga, TN
Age: 45
Posts: 7,646
Vehicle: 87 D21 SE KC V6 2wd 5sp & 86.5 V6 SE auto
Thanks: 253
Thanked 813 Times in 757 Posts
Default

factory 14in nissan, yes.
cadillacdude1975 is offline   Reply With Quote
Old 05-22-2015, 03:24 PM   #86
DesertRunner
 
Join Date: May 2015
Location: AL
Posts: 99
Vehicle: 1988 Nissan D21 Desert Runner
Thanks: 13
Thanked 8 Times in 8 Posts
Default

Asking for clarity. For me to change the 88 Desert Runner front drums over to the Pathfinder Rotors I need the calipers, discs, and pads I know for sure. Do I need the hub and spindles from a Pathfinder as well? Also what about the master cylinder and brake lines?
DesertRunner is offline   Reply With Quote
Old 05-24-2015, 05:19 AM   #87
scoobysmak
Xtreme Lowz
 
scoobysmak's Avatar
 
Join Date: Jan 2011
Location: Southeast TN
Age: 43
Posts: 3,111
Vehicle: 90 KA24 2wd Std Cab, 91 SR20DET 2wd Ext Cab
Thanks: 320
Thanked 399 Times in 377 Posts
Default

Quote:
Originally Posted by DesertRunner View Post
Asking for clarity. For me to change the 88 Desert Runner front drums over to the Pathfinder Rotors I need the calipers, discs, and pads I know for sure. Do I need the hub and spindles from a Pathfinder as well? Also what about the master cylinder and brake lines?
I am shocked that the Desert Runner ran front drum brakes but I would have to see a picture of your spindle and compare it to pic of a 4x4 spindle, I maybe a few 4x4 guys will know.

I would suggest the brake lines at least since you will have to remove the lines from the drum anyway. That rubber, if its factory, is over 27+ years old; small price to pay to insure your safety. I would think the master cylinder is the same but honestly don't know.
__________________
The Kids= Down N Out: 91 Nissan Ext Cab, SR20DET, Build Thread: http://www.infamousnissan.com/forum/...ad.php?t=20041
The daily: 90 Nissan Std Cab, KA24, Build thread:http://www.infamousnissan.com/forum/...476#post413476

87 Nissan Pathfinder...on hold... , 93 Nissan Pickup Long Bed.....needs help!!!
scoobysmak is offline   Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT. The time now is 12:06 PM.


Powered by vBulletin® Version 3.8.6
Copyright ©2000 - 2017, Jelsoft Enterprises Ltd.