Go Back   Infamous Nissan - Hardbody / Frontier Forums > Search Forums

Showing results 1 to 11 of 11
Search took 0.01 seconds.
Search: Posts Made By: Framebender
Forum: Wiring and Electrical 07-21-2018, 04:48 PM
Replies: 10
Views: 275
Posted By Framebender
https://ibb.co/e6Y9Wy this is what I have...

https://ibb.co/e6Y9Wy
this is what I have found.
https://ibb.co/e6Y9Wy
Forum: Wiring and Electrical 07-21-2018, 04:27 PM
Replies: 10
Views: 275
Posted By Framebender
Thanks a bunch for the pic now i have something...

Thanks a bunch for the pic now i have something to hunt for.
Forum: Wiring and Electrical 07-08-2018, 06:37 AM
Replies: 10
Views: 275
Posted By Framebender
There isnt any heat shield on the manifold only...

There isnt any heat shield on the manifold only near the collector and I dont see any bracket there. The engine has been out of this truck a few times so theres a few plugs unplugged on the drivers...
Forum: Wiring and Electrical 07-04-2018, 04:36 AM
Replies: 10
Views: 275
Posted By Framebender
KA24e o2 sensor question

The previous owner of my truck deleted the O2 sensors and I'd like to reinstall them. My problem is locating the plugs on the harness for the sensors. If anyone could help me out I would appreciate...
Forum: Hardbody Forum (D21) 05-03-2018, 10:07 PM
Replies: 10
Views: 426
Posted By Framebender
Ok so I found the noise before I pulled the...

Ok so I found the noise before I pulled the engine. Turns out when i meshed the engine and trans something with the clutch was hitting. My neighbor says throw out bearing wasn't seating right. It...
Forum: Hardbody Forum (D21) 05-02-2018, 06:18 AM
Replies: 10
Views: 426
Posted By Framebender
The engine had a slight knock so i rebuilt it....

The engine had a slight knock so i rebuilt it. New bearings, pistons, oil pump all the goodies. On the initial start up there was some noise but most of it went away as soon as oil pressure built up....
Forum: Hardbody Forum (D21) 05-02-2018, 03:37 AM
Replies: 10
Views: 426
Posted By Framebender
I guess I have to pull the motor then and tear it...

I guess I have to pull the motor then and tear it down.
Forum: Hardbody Forum (D21) 05-02-2018, 12:14 AM
Replies: 10
Views: 426
Posted By Framebender
Timing chain too tight?

I just finished a rebuild on my 90 d21 ka24e. The engine has a knockwitrh fresh bearings in it. When I put the timing set on I noticed the timing chain was tight without the pin pulled on the...
Forum: Engine and Drivetrain 05-02-2018, 12:10 AM
Replies: 1
Views: 193
Posted By Framebender
Timing Issue(Need help)

So I pulled my engine and did a rebuild on it. When I got to the timing set I noticed the chain was really tight without the pin pulled on the tensioner. Is this normal? When I started the engine...
Forum: Suspension 03-16-2018, 09:43 PM
Replies: 2
Views: 332
Posted By Framebender
The tie rods all fit into the link but the link...

The tie rods all fit into the link but the link doesnt fit into the pitman arm that great. Is the drag link supposed to have one side that acts like a ball joint and one side thats supposed to swivel...
Forum: Suspension 03-16-2018, 06:08 PM
Replies: 2
Views: 332
Posted By Framebender
Drag link problem

I replaced the drag link and tie rods with a cheap ebay kit. The idler arm made the tie rod on the passenger side rub the frame that the lower control arm connects to so I had to reuse the old one....
Showing results 1 to 11 of 11

 
Forum Jump

All times are GMT. The time now is 09:42 AM.


Powered by vBulletin® Version 3.8.6
Copyright ©2000 - 2018, Jelsoft Enterprises Ltd.