Go Back   Infamous Nissan - Hardbody / Frontier Forums > Search Forums

Showing results 1 to 25 of 500
Search took 0.26 seconds.
Search: Posts Made By: SBJ
Forum: Hardbody Forum (D21) Yesterday, 04:30 PM
Replies: 15,832
Views: 1,069,712
Posted By SBJ
Mine was done at 125K. I think that had more to...

Mine was done at 125K. I think that had more to do with the previous owner's driving habits than anything else. 10K on the new clutch and it barely feels broken in.
Forum: Hardbody Forum (D21) Yesterday, 04:45 AM
Replies: 15,832
Views: 1,069,712
Posted By SBJ
Hey scifi, If you still have the...

Hey scifi,

If you still have the transmission in the truck put it in gear before pulling it. That way if the input shaft isn't quite lined up when you go to reinstall you can reach around back...
Forum: General Discussion 01-18-2018, 06:59 PM
Replies: 10
Views: 127
Posted By SBJ
Oh man! Once on my old Accord 2.2 (non-vtec) I...

Oh man! Once on my old Accord 2.2 (non-vtec) I decided to adjust the valves the quick and dirty way... with the engine running. After I got done and drove it around my passenger legitimately...
Forum: Hardbody Forum (D21) 01-17-2018, 04:01 AM
Replies: 15,832
Views: 1,069,712
Posted By SBJ
Damn. I wish we had an advance up here. The oil...

Damn. I wish we had an advance up here. The oil pan gasket is a good idea, if it's like the KA24 there's an aluminum plate that bolts to both the block and the oil pan and it has to come out to do...
Forum: Hardbody Forum (D21) 01-17-2018, 12:12 AM
Replies: 15,832
Views: 1,069,712
Posted By SBJ
Fireworks in the snow are a blast too. We used...

Fireworks in the snow are a blast too. We used to have exploding snowball fights and would blow up our forts when we were done with them.
Forum: Hardbody Forum (D21) 01-16-2018, 06:38 PM
Replies: 15,832
Views: 1,069,712
Posted By SBJ
No idea. I've heard it's not easy and requires...

No idea. I've heard it's not easy and requires removing the driver's side torsion bar.
Forum: Hardbody Forum (D21) 01-16-2018, 05:27 PM
Replies: 15,832
Views: 1,069,712
Posted By SBJ
2wd. I've had my tranny out twice. Once I...

2wd. I've had my tranny out twice. Once I realized I could pick it up myself I didn't even bother using a jack to put it back in. I only used the jack to hold it up while I got the cross member...
Forum: Hardbody Forum (D21) 01-16-2018, 03:58 PM
Replies: 15,832
Views: 1,069,712
Posted By SBJ
Hey Scifi, You might not even need the...

Hey Scifi,

You might not even need the transmission jack. The transmission weighs just under 85lb fully assembled with the fluid drained out. I found it was easier to bench press it in and out...
Forum: Project Build Log 01-15-2018, 01:37 AM
Replies: 169
Views: 2,757
Posted By SBJ
RWD for the win! Until it snows or you want to...

RWD for the win! Until it snows or you want to go out in the woods...
Forum: Project Build Log 01-14-2018, 04:53 AM
Replies: 169
Views: 2,757
Posted By SBJ
That's good. It means you did it right.

That's good. It means you did it right.
Forum: Engine and Drivetrain 01-14-2018, 04:52 AM
Replies: 15
Views: 776
Posted By SBJ
Alright, cool. I'll go through the old thread...

Alright, cool. I'll go through the old thread and see if the pictures are still working. Sorry, I couldn't find a picture of the countershaft with the first gear removed.
Forum: Hardbody Forum (D21) 01-14-2018, 03:20 AM
Replies: 8
Views: 103
Posted By SBJ
Yup...the casing on mine was cracked in half from...

Yup...the casing on mine was cracked in half from where somebody had busted the lock open with a screwdriver. It also needed a radio lol. The guy I bought it from hadn't locked it in 15 years!
Forum: Engine and Drivetrain 01-13-2018, 06:34 PM
Replies: 15
Views: 776
Posted By SBJ
I rebuilt my transmission about a year ago and I...

I rebuilt my transmission about a year ago and I still have some pictures of the guts kicking around somewhere, although photobucket probably wants $400 a year for them. I can re-upload them if it...
Forum: Hardbody Forum (D21) 01-13-2018, 05:29 PM
Replies: 8
Views: 103
Posted By SBJ
They are. I swapped mine over no problem. I...

They are. I swapped mine over no problem. I might have taken the screw off in the back and flipped the arm 180 degrees, I can't remember. You'll probably want to hit the metal retaining plate with...
Forum: Project Build Log 01-13-2018, 04:11 AM
Replies: 169
Views: 2,757
Posted By SBJ
Man I have broken so many bicycle and lawnmower...

Man I have broken so many bicycle and lawnmower type cables it's not even funny. Great stuff, here's to a regular and uneventful startup. Still looking forward to the teardown of the old one.
Forum: Hardbody Forum (D21) 01-11-2018, 05:53 PM
Replies: 39
Views: 486
Posted By SBJ
I had already replaced both when I did the brakes...

I had already replaced both when I did the brakes the first time. It was a cheap shitty reman one that failed. Both have since been replaced.

Luckily I was just pulling into the parking lot at...
Forum: Hardbody Forum (D21) 01-11-2018, 05:11 PM
Replies: 39
Views: 486
Posted By SBJ
Wheel cylinders always seem to leak first. I...

Wheel cylinders always seem to leak first. I actually had one fail quite spectacularly to where it sprayed brake fluid all over the inside of the drum and I lost all pressure in the pedal. After...
Forum: Project Build Log 01-11-2018, 05:18 AM
Replies: 30
Views: 4,444
Posted By SBJ
It started and ran before you tore into it,...

It started and ran before you tore into it, right? I would check the ground for the crank position sensor. It's a little spade connector on the side of the distributor that plugs into a little...
Forum: Hardbody Forum (D21) 01-11-2018, 03:46 AM
Replies: 39
Views: 486
Posted By SBJ
I agree with the above, sounds like a bad master...

I agree with the above, sounds like a bad master to me. Especially if your fluid level isn't going down. Typically a bad booster will cause the opposite and the pedal will get really stiff. If...
Forum: General Discussion 01-10-2018, 05:24 AM
Replies: 13
Views: 241
Posted By SBJ
Bringing some old pictures back from the dead. ...

Bringing some old pictures back from the dead. The EGR solenoid is boxed in red. I believe a standard fuel injector connector will fit it. I typically use a 9V battery to test them, even though...
Forum: General Discussion 01-10-2018, 01:56 AM
Replies: 13
Views: 241
Posted By SBJ
Yeah man it's a pain. Rule out everything else...

Yeah man it's a pain. Rule out everything else before tearing into it. If you do decide the valve needs to come off you'll need a 30mm open end wrench or a large crescent wrench. I think I have a...
Forum: General Discussion 01-10-2018, 12:52 AM
Replies: 13
Views: 241
Posted By SBJ
Check that the solenoid is working when you apply...

Check that the solenoid is working when you apply power to it. It's kind of underneath the idle control valve and it's not terribly hard to get to. I got an old picture I'll post up later when I'm...
Forum: Hardbody Forum (D21) 01-08-2018, 11:20 PM
Replies: 67
Views: 885
Posted By SBJ
Dead blow hammer if you got one. To avoid...

Dead blow hammer if you got one. To avoid damaging the teeth on the sprocket you can put the dead blow hammer against it and hit the back of it with another hammer if you need more force. I agree...
Forum: The Other Forum 01-08-2018, 09:36 PM
Replies: 5
Views: 111
Posted By SBJ
Glad to hear it! My mom has a similar vintage...

Glad to hear it! My mom has a similar vintage v70 wagon with the same engine. It's an absolute cluster fuck of an engine and it looks like they built the whole front end of the car around it. I...
Forum: The Other Forum 01-08-2018, 04:19 AM
Replies: 5
Views: 111
Posted By SBJ
You have a couple of options. The first is to...

You have a couple of options. The first is to get a set of torx allen keys. They have the same 90 degree bend an allen wrench does but they have a torx on the end. The second is to get a t25 torx...
Showing results 1 to 25 of 500

 
Forum Jump

All times are GMT. The time now is 03:03 AM.


Powered by vBulletin® Version 3.8.6
Copyright ©2000 - 2018, Jelsoft Enterprises Ltd.