Go Back   Infamous Nissan - Hardbody / Frontier Forums > Search Forums

Showing results 1 to 25 of 69
Search took 0.01 seconds.
Search: Posts Made By: urimashe
Forum: Hardbody Forum (D21) 11-08-2018, 05:09 PM
Replies: 161
Views: 2,829
Posted By urimashe
Yea, feels great, Last time I did a motor on the...

Yea, feels great, Last time I did a motor on the ka24e hardbody I had the firing order wrong. I thought I did something wrong putting the motor back together.
Forum: Hardbody Forum (D21) 11-07-2018, 10:28 PM
Replies: 161
Views: 2,829
Posted By urimashe
GOOD NEWS! Last Saturday I got everything...

GOOD NEWS! Last Saturday I got everything finished, tail light in, exhaust gaskets, 4wd hooked back up, everything, vehicle is happy, fires up first crank every time. I had some photos taken of the...
Forum: Hardbody Forum (D21) 10-31-2018, 12:42 AM
Replies: 161
Views: 2,829
Posted By urimashe
Building a boosted Vg30 is the idea. could buy a...

Building a boosted Vg30 is the idea. could buy a nice forged or billet crank, rods, pistons. check the deck for flatness, polish the heads, bore the cylinders. at that point it would be perfect for...
Forum: Hardbody Forum (D21) 10-30-2018, 08:08 PM
Replies: 161
Views: 2,829
Posted By urimashe
Yea, days have been getting shorter, The temp has...

Yea, days have been getting shorter, The temp has been pretty warm, just got down below freezing here on sunday, and it snowed. but its suppose to warm up again, its all due to the warmer ocean temps...
Forum: Hardbody Forum (D21) 10-23-2018, 03:22 AM
Replies: 161
Views: 2,829
Posted By urimashe
Engine is in, accessories are hooked, up, this...

Engine is in, accessories are hooked, up, this Saturday i will have the trans bolted to the engine, the front dif in, the radiator back in and everything hooked up and ready to fire up, if all goes...
Forum: Hardbody Forum (D21) 10-13-2018, 11:07 PM
Replies: 161
Views: 2,829
Posted By urimashe
Well, napa screwed up on ordering parts for my...

Well, napa screwed up on ordering parts for my engine, I got the oil pump reinstalled but its missing its crank seal, I went and put the separator plate on and the flywheel, removed the pilot bushing...
Forum: Hardbody Forum (D21) 10-08-2018, 03:28 AM
Replies: 161
Views: 2,829
Posted By urimashe
So i took the engine out, started swapping stuff...

So i took the engine out, started swapping stuff over to the new engine, resealing the new engine. replaced timing belt, and got ready to put the timing cover on, and realized the oil pump is...
Forum: Hardbody Forum (D21) 09-16-2018, 07:59 PM
Replies: 161
Views: 2,829
Posted By urimashe
I use ford motocraft stuff. since thats who i...

I use ford motocraft stuff. since thats who i work for. we have this high grade stuff that we use on vehicles that need sealing in high hear high oil areas such as oil pants and intake manifolds....
Forum: Hardbody Forum (D21) 09-14-2018, 05:41 AM
Replies: 161
Views: 2,829
Posted By urimashe
sorry for the late update, been busy. i got a few...

sorry for the late update, been busy. i got a few photos of the new engine torn down, and the old one partly town down, but getting them off my phone and on to my computer to post them is... tedious...
Forum: Hardbody Forum (D21) 09-06-2018, 06:32 PM
Replies: 161
Views: 2,829
Posted By urimashe
yea, figured as much, well its good I got the...

yea, figured as much, well its good I got the round, gonna order the belt and water pump shortly. though, the belt and pump on this motor looks relatively new, wonder when it was replaced, its...
Forum: Hardbody Forum (D21) 09-06-2018, 04:52 PM
Replies: 161
Views: 2,829
Posted By urimashe
here is my timing gears. think its round tooth?...

here is my timing gears. think its round tooth? least the belt has round teeth, the gears only have a round gullet lol.

http://i66.tinypic.com/f0afb7.jpg
Forum: Hardbody Forum (D21) 09-06-2018, 04:47 PM
Replies: 161
Views: 2,829
Posted By urimashe
it has a 36 gallon tank i believe, this one was...

it has a 36 gallon tank i believe, this one was geared for travel, so it does decent on the highway, i can get 350 to 360 miles to a tank, but it sucks fuel in town, i don't miss it for its fuel...
Forum: Hardbody Forum (D21) 09-06-2018, 12:00 AM
Replies: 161
Views: 2,829
Posted By urimashe
sadly, no extra money for headers right now, i...

sadly, no extra money for headers right now, i need to get this truck done fast, my g30 van cost me 85 dollars to fill it up. i felt that hard, lol. so hopefully by the weekend after next I can have...
Forum: Hardbody Forum (D21) 09-05-2018, 06:11 PM
Replies: 161
Views: 2,829
Posted By urimashe
headers wont be until further down the road....

headers wont be until further down the road. ordered my gaskets yesterday, they should arrive on Saturday, today im going to try and pull part of the timing cover on the new engine just to see what...
Forum: Hardbody Forum (D21) 09-05-2018, 02:12 AM
Replies: 161
Views: 2,829
Posted By urimashe
figured as much, i was looking at some headers,...

figured as much, i was looking at some headers, they would be nice, and look easy enough to install, taking the diff out took a couple hours, even with a lift, was like a big puzzle, it should go in...
Forum: Hardbody Forum (D21) 09-04-2018, 08:33 PM
Replies: 161
Views: 2,829
Posted By urimashe
this engine is rather spotless, I feel like I...

this engine is rather spotless, I feel like I should just drop it in and swap parts and be done, but I am going to replace the rear main seal, the front if I can, the timing belt and water, pump, get...
Forum: Hardbody Forum (D21) 09-04-2018, 06:56 PM
Replies: 161
Views: 2,829
Posted By urimashe
Saturday I took the front diff out in prep for...

Saturday I took the front diff out in prep for pulling the motor, this coming Saturday the old motor will be pulled. I know the oil pan will need to be swapped, as well as the manifolds and intake.
Forum: Hardbody Forum (D21) 09-01-2018, 05:33 PM
Replies: 161
Views: 2,829
Posted By urimashe
Its vg30 996313 is the serial number on the block

Its vg30 996313 is the serial number on the block
Forum: Hardbody Forum (D21) 09-01-2018, 03:31 AM
Replies: 161
Views: 2,829
Posted By urimashe
http://i63.tinypic.com/2lc44jp.jpg here...

http://i63.tinypic.com/2lc44jp.jpg


here it is.
Forum: Hardbody Forum (D21) 08-31-2018, 10:13 PM
Replies: 161
Views: 2,829
Posted By urimashe
The new engine has arrived yesterday, and I...

The new engine has arrived yesterday, and I picked her up today. the only part I am not happy about, They put the engine down on the pallet on her side. I was always taught that that was a no no for...
Forum: Hardbody Forum (D21) 08-24-2018, 08:14 PM
Replies: 161
Views: 2,829
Posted By urimashe
either way, I will get it done, tomorrow...

either way, I will get it done, tomorrow (Saturday) I will pull the truck in to my stall, lift it and see about getting the engine out, my new engine should arrive next Friday, or Saturday. they...
Forum: Hardbody Forum (D21) 08-24-2018, 03:06 AM
Replies: 161
Views: 2,829
Posted By urimashe
some repairs you can do with the cab on, other...

some repairs you can do with the cab on, other repairs require the cab to come off. our diesel mechanics can lift a cab pretty quick.
Forum: Hardbody Forum (D21) 08-24-2018, 12:24 AM
Replies: 161
Views: 2,829
Posted By urimashe
well, I work in a shop with plenty of tools, and...

well, I work in a shop with plenty of tools, and lifts, so, one way or another, that engine is coming out.

I thought about just lifting the whole cab off, the issue I run in to there though is...
Forum: Hardbody Forum (D21) 08-23-2018, 10:04 PM
Replies: 161
Views: 2,829
Posted By urimashe
Ah, well it looks like I will have to do it my...

Ah, well it looks like I will have to do it my way then. when I did my Ka24e, I undid the body mounts, lifted the cab 2 inches, allowing the trans and engine to angle upwards, that allowed me to stab...
Forum: Hardbody Forum (D21) 08-23-2018, 06:30 PM
Replies: 161
Views: 2,829
Posted By urimashe
does anyone know if the engine and trans has to...

does anyone know if the engine and trans has to come out at the same time on a manual v6 hardbody? I thought I read somewhere that the input shaft does not interfere with the engine/clutch when...
Showing results 1 to 25 of 69

 
Forum Jump

All times are GMT. The time now is 10:52 PM.


Powered by vBulletin® Version 3.8.6
Copyright ©2000 - 2018, Jelsoft Enterprises Ltd.