Infamous Nissan - Hardbody / Frontier Forums

Infamous Nissan - Hardbody / Frontier Forums (http://www.infamousnissan.com/forum/index.php)
-   Nissan Cars (http://www.infamousnissan.com/forum/forumdisplay.php?f=43)
-   -   Altima Immobilization System (http://www.infamousnissan.com/forum/showthread.php?t=43673)

jp2code 12-07-2019 11:02 PM

Altima Immobilization System
 
OK, this is going to be a long shot here. I've posted this on a couple of other Nissan forums since this forum is specific to the Hardbody and Frontier, but I have gotten 0 replies in the last 2 days.

This is long. I apologize, but I want everyone to know what happened.

I have a 2012 Altima with the push button start.

About a week ago, I was working on my aftermarket car stereo because the electrical ground was not making it to the battery. To work on the stereo, I took the center vents out that contain the airbag activation light, which I unplugged so the wire would not have any strain. It remained that way a couple of days while I debugged the intermittent issue, and the airbag warning light blinked in the instrument cluster.

After fixing the stereo and reconnecting the airbag activation light, the airbag warning light in the instrument cluster was still blinking.

I posted a question on one of the Facebook groups about how to get the warning light to reset, and someone told me how to cycle the power 4 or 5 times until the light stops coming on. I was tired from a 12-hour shift, so I wasn't really counting, but I gave up and stopped somewhere around 10 times.

When I got in to drive to work later that day, the car would not do anything. The push button light is ON, and blinks OFF shortly every 15 seconds and goes back ON.

The brake pedal usually gives a little I push the brake to crank, but now it is firm.

The push button does not work at all unless I have the key fob plugged into the fob port.

I had the local Nissan dealership send a technician out. He plugged his consult into the port; we could see the consult register when we turned the car to ACCESSORY/ON, pressed the brake pedal, and a number of other things, but there were no errors. He removed the battery and did a factory reset of the ECU, but there was no change. He said I should have Nissan replace the brake switch, but I pointed out that the brake lights were still coming on when he pressed on the brakes. Then he started talking about needing to replace the ECU, but I pointed out that he had the consult port plugged into the ECU and it was confirming everything. He agreed with the logic of both my findings, and he could not find any reason why the car would not start. He said I would need to have it towed to Nissan where they could do more tests.

My car does not have a warranty. I imagine if I bring my car there, they are going to start replacing all sorts of stuff because that's what they usually do and what usually gets charged to warranty. I cannot get other shops in town to look at it because they aren't sure what would cause this, even though I keep mentioning the Immobilization System.

I have tried various techniques to clear my issue (like the Nissan technician did), but nothing has worked yet.

With all that said, does anyone here have any experience with this type of issue?

https://i.imgur.com/pZO9xRz.png

alabama_lowlife 12-07-2019 11:43 PM

Are you sure the brake lights and the ecu use the same switch? My Titan had a switch for the lights and a separate switch for the shift lock solenoid.

jp2code 12-08-2019 12:08 AM

I'm not sure about anything.

I'm inclined to think that it isn't a problem with the switch just because everything worked fine until I did the start sequence to reset the airbag light.

But I don't know.

mytmouz 12-08-2019 12:26 AM

This is what I always did on my older Sentra to reset any lights on then. I replaced the airbags and airbag computer on one with used stuff, it didnt crank afterwards, until I did this...

pen driver door
Get in
Shut door
Turn ignition to the on position The one that will go all the way, but not to start car)
Open door
Reach down with your right hand if your a rightty
Press the door ajar sensor button thing (7) times
Shut door
Start your car

SBJ 12-08-2019 12:32 AM

What Mytmouz said. I was going to reply with a couple of ideas but I can't top that.

To turn the ignition on (but not start it): Press the start/stop button WITHOUT your foot on the brake. I think you have to press it twice but I'm not sure. You'll know it when all the dash lights come on. If your brake lights come on and you can shift out of park (with the ignition on) I doubt your brake light switch is bad.

jp2code 12-08-2019 06:59 PM

What does "pen driver door" mean?

nunya 12-08-2019 07:15 PM

"open" driver door, maybe?

mytmouz 12-09-2019 01:58 AM

Open I must have missed a letter on the copy n paste. I have this in my files for when I need it. It is getting harder to hold my phone or tablet to proofread...

cadillacdude1975 12-09-2019 04:35 AM

My dad had a jeep grand cherokee once. The anti theft/immobilization system went bonkers and rendered the vehicle useless. he had to pay a tech to remove the mess.

SBJ 12-09-2019 05:53 AM

Quote:

Originally Posted by cadillacdude1975 (Post 528553)
My dad had a jeep grand cherokee once. The anti theft/immobilization system went bonkers and rendered the vehicle useless. he had to pay a tech to remove the mess.

I hate those things. IMHO they are some of the biggest pieces of crap on the road.


All times are GMT. The time now is 01:16 AM.

Powered by vBulletin® Version 3.8.6
Copyright ©2000 - 2020, Jelsoft Enterprises Ltd.