Infamous Nissan - Hardbody / Frontier Forums

Infamous Nissan - Hardbody / Frontier Forums (http://www.infamousnissan.com/forum/index.php)
-   4x4 and Offroading (http://www.infamousnissan.com/forum/forumdisplay.php?f=49)
-   -   4x4 shifter seal and boot? (http://www.infamousnissan.com/forum/showthread.php?t=41935)

Shawn B13 08-12-2018 06:12 PM

4x4 shifter seal and boot?
 
'94 V6, 4x4, automatic



New to these trucks.


I cannot find the name of, or part numbers, to the rubber seal/boot (with metal trim ring) and the outer leather boot (with snaps) that goes over the 4x4 shift lever.


Without them, I have a very nice constant blowing heater in August in Louisiana.



Thanks.

cadillacdude1975 08-12-2018 07:43 PM

send david29 a message. he is the parts man around here.

Shawn B13 08-13-2018 05:28 PM

Quote:

Originally Posted by cadillacdude1975 (Post 507959)
send david29 a message. he is the parts man around here.

Thank you sir.

cadillacdude1975 08-13-2018 10:40 PM

Anytime.

Shawn B13 09-10-2018 02:38 PM

Crown Automotive J5353263 Transfer Case Boot
 
Addressed my Fred Flintstone hot engine air circulation issue from no Nissan oem or aftermarket chassis specific replacement for the transfer case rubber (or leather) boots.

However, by measuring and eye-balling, I ordered a Crown Automotive J5353263 Transfer Case Boot (currently $20 on Amazon). You have to drill two (2) holes and punch three (3) holes to install slick as hell. No trimming or other mods necessary.

Crown boot, base listed as 4 X 8".
https://i.imgur.com/hdk1B1U.jpg


Before:
https://i.imgur.com/kYIQfXg.jpg

Finished installation. Don't have the leather trim (yet) but that "could be" a Nissan boot it fits so nicely.
https://i.imgur.com/Wi3XOHY.jpg


https://i.imgur.com/Bp9NvfT.jpg

Finished with center console removed.
https://i.imgur.com/vw89hGl.jpg

You just put the Nissan trim ring up one full fold of rubber on the "pyramid". Then punch/drill your holes where required. I drilled the rubber for the two (2) factory studs, and punched it for the three (3) factory screws. Note the factory forward bracket in the pic, that had to be removed for install, or you'd have to trim the rubber boot.
https://i.imgur.com/1aITTP5.jpg

The rubber does not stick out on the left, but it is just under the lip of the trim ring. Plenty of overlap for clamping down securely.
https://i.imgur.com/w1rmzJ1.jpg

You can see the oem screw goes right through the rubber.
Note: That damn trim ring is SHARP. Non-finished at the factory. I cut myself, then sanded the entire circumference of the ring before proceeding with installation.
https://i.imgur.com/xOyBG3X.jpg

Getting all civilized in my cabin. :dathumb:

Shawn B13 09-10-2018 02:41 PM

I have no clue how to resize photos. Sorry for any inconvenience.

Jojoroxx 05-04-2020 07:27 PM

Thank you for this post I took the trouble to register so I could appreciate you explaining this so nicely and hooking us up with the right part number. Nissan LOYAL!!

nctexan 07-24-2021 01:16 PM

Bringing this back from the dead - Thanks Shawn for the write up and link, I was able to find the exact same boot (though it's $30 now!).

The only thing I can't figure and am even more confused after seeing your pics is how to remove the shifter knob? Mine is actually different than yours, it doesn't just go from the knob to the single shifter diameter, it's attached to a bigger diameter shaft that fits over the shaft diameter shown on yours.

In other words, I'm leaning towards someone replaced the shifter knob and permanently glued it onto the OEM shaft. So I think I'm going to either have to cut the knob off and install another aftermarket and/or cut the brand new pristine boot and tape it back together or something, which is kind of depressing. Will put some pics up later.


All times are GMT. The time now is 05:05 PM.

Powered by vBulletin® Version 3.8.6
Copyright ©2000 - 2021, Jelsoft Enterprises Ltd.