"...a Sentra?"

[1fastser]

That's usually what I hear after beating someone at the track...it's very amusing.

The build can be seen in the link HERE. (http://picasaweb.google.com/serious1tx/TheBeastBuildup#)

Here are a couple of pics...

http://lh4.ggpht.com/_aYj30dmCSvw/SvVyYPsKmOI/AAAAAAAADsg/KdwwgeUBbxg/beast1.jpg

http://lh6.ggpht.com/_aYj30dmCSvw/SvVyYX5nYVI/AAAAAAAADso/yN9UDVyvK04/beast2.jpg

sleeper gauges :)
http://lh5.ggpht.com/_aYj30dmCSvw/SvVyYt3pngI/AAAAAAAADss/uV5QjcCYhx0/beast3.jpg

http://lh5.ggpht.com/_aYj30dmCSvw/SCdktixzCsI/AAAAAAAAB2A/TafzYQFMMgQ/s512/Motor2.jpg

http://lh5.ggpht.com/_aYj30dmCSvw/SCdkzixzC7I/AAAAAAAAAY0/s6SKpPhF8Lc/Motor15.jpg

http://lh4.ggpht.com/_aYj30dmCSvw/SCdlOSxzD-I/AAAAAAAAAhQ/U4NckNsjpn4/s640/complete.jpg

...the mod list is long. :D It's built more for top end and is viscious in 4th and 5th. I'm in Viper territory :nana2:

[97redhardbody]

Sweet!!!!!!

[1fastser]

My Silvia. (http://www.infamousnissan.com/forum/showthread.php?t=6263)

[pugz]

nice car..... viper territory huh..... how fast u plan on taking this thing ? :D:D:D

[1fastser]

Well :D I plan on taking it to the Texas Mile next go-round...

With pump gas, my butt-dyno tells me it's around 360-370fwhp at 12psi. Boost doesn't come on 'till almost 4000rpms so i can stay out of boost and still get 27mpg! It'll break the tires loose rolling into third. :D

With race gas and water injection however, it's a different animal that can run 24psi of boost! I have yet to tame this one.

It's a blast!

[97redhardbody]

Well :D I plan on taking it to the Texas Mile next go-round...

With pump gas, my butt-dyno tells me it's around 360-370fwhp at 12psi. Boost doesn't come on 'till almost 4000rpms so i can stay out of boost and still get 27mpg! It'll break the tires loose rolling into third. :D

With race gas and water injection however, it's a different animal that can run 24psi of boost! I have yet to tame this one.

It's a blast!

hell yeah that sounds sick. any vids of it?

[SkinnyG]

Hypercoils and AGX's. Nicely done. What are you running for sway bars? I used to run OEM front and ST rear bar. A bit twitchy, but great for FSP solo II. Whiteline offset bushings (KAC303 I think....) were very good.

[1fastser]

Yea it tends to push a bit and i was gonna switch back to a stock front. Here's a current mod list...hope you have some reading time :)

* Engine
USDM block (I really can't remember at this point) drilled for turbo oil drain
OE 300ztt pistons and rings
Nissan upgraded cam oiling tubes
Cobra MAF
Rocker Arm Stoppers
JWT Solid Mounts
JWT S3 Cams
JWT Adjustable Cam Gears
JWT ECU with H20 Injection
JWT Fuel Rail - powder coated black
Valve Cover – powder coated black
MSD 72# Injectors
NISMO Fuel Pressure Regulator
Walbro 255 LPH Fuel Pump
Full 3” exhaust from someone in FL (?) w/ Universal 3" Muffler
FMAX 2.5” to 3” Down Pipe - Swain White Lightening coating
FMAX Log Manifold – Ceramic Coated
FMAX Intercooler - Swain Stealth Coat
FMAX IC Plumbing – Coated Blue
Garrett T3/T04E Turbo - Stage V wheel 60/.82 A/R
TIAL 35 mm Wastegate – Divorced
Greddy Type-R BOV
Crane Hi-6 Ignition
Crane Hi-6 Coil LX-92
OEM Spark Plug Wires
N1 water pump pulley aluminum from GSPEC
N1 Front cover
N1 Crank pulley
N1 Sump
Innovative Turbo Black Silicon Hoses
Greddy Oil Separator Can
Greddy Custom Oil Filter Relocation Setup
Slim High RPM Cooling Fans w/ trimmed OE fan shroud
Royal Purple Ice
Royal Purple Oil
Redline Power Steering Fluid

* Tranny
SR20Dev Transmission – Welded & Cryo’d
QUAIFE!
ACT Clutch Extreme PP & Street disk
ACT Lightweight Flywheel
B&M Short Shifter
Redline Shockproof

* Outside
Tsuru Front Headlight Conversion – Custom Grille
Custom Front Airdam
Sunny Super Saloon Side Skirts
Removed Emblems
Enkei RP01s

* Underside
KYB AGX
Hyperco Gen II
Suspension Techniques f/r sway bars
Full ES Bushing Kit
Goodrich Stainless Steel Brake lines

* Inside
Momo Shift Knob
Momo Pedals
Momo Steering Wheel
Optima Red Battery trunk-mounted
Greddy Vacuum / Boost Gauge Mechanical
Greddy Exhaust Gas Temperature Gauge Mechanical
Stewart Warner Oil Pressure Gauge Mechanical
Stewart Warner Water Temperature Gauge Mechanical
Stewart Warner Oil Temperature Gauge Electrical
Greddy Profec B
Apexi Turbo Timer
Brand New Headliner

:D

[SkinnyG]

Ouch. Front ST bar: Ditch! Ditch! Ditch! It majorly binds the front suspension. Lose it asap. The rear ST is great, but it will be twitchy. If you're buying again, get the Progress bars.

I also found that a lower strut bar (tie the lower control arms together) made a phenomenal improvement. $5 of fabrication:

http://img.photobucket.com/albums/0903/skinnyg/Sentra/DSC00656.jpg

My B13 was an XE. Motor was bone stock, but I autocrossed in F/SS in Canada. Came second in the Canadian Nationals with it in 2003. Nice to see one again. I can't believe I miss mine.

[1fastser]

You have an oil leak.

[SkinnyG]

No I don't.

I have several.

[jr.]

beautiful car..

[Prime Ministah]

nice ride. old school trick for fwd is no front sway at all, and put the largest you can get for the back.

[sunsetjesse]

looks great bro do u have any videos it running and wat r the specs on the motor like balance weight and bore size and did u port and polish the head.

[1fastser]

nice ride. old school trick for fwd is no front sway at all, and put the largest you can get for the back.

Stock front with ST rear is also a nice ride and easy to 'throw around' too...

[1fastser]

looks great bro do u have any videos it running and wat r the specs on the motor like balance weight and bore size and did u port and polish the head.


I'm too secret.

[Mr.Ryan]

Wow sweet B13, I love the 85-94 sentras, I'm a lil more partial to the 85-90 style tho, and your list of mods is definitely something to drool over, not to jack your thread but this is one of my favorite B12's of all time.

http://carphotos.cardomain.com/ride_images/3/3493/1041/33730520002_large.jpg

[1fastser]

No worries, I'm a fan.

[sunsetjesse]

damn i need some ideas cuz when im done with the motor on my hb im looking for about 250-300 horse without nitrous or turbo.

[balyon85]

Have any more pictures of the turbo inlet tubing? I kinda want to run my tubing like yours, I hate the way most turboed B15s have there filter sitting in the bay, yours looks way cleaner.