Exhaust pics....

[Ratrod25]

My exhaust hangs retarded low.. Does any body have pics of there exhaust set ups? Perferably(sp) some body with a stock frame? I almost have drug a few holes in it already.. other than these i havent seen any body elses

This i got from DISTURBEDPUP

http://i295.photobucket.com/albums/mm156/Ratrod25/user880_pic2785_1243373197.jpg

this one from nis720

http://i295.photobucket.com/albums/mm156/Ratrod25/IMG_0335a.jpg[/QUOTE]

[lilFlip]

i'll get some for you tomorrow, my tranny crossmember is notched on the top....

[Ratrod25]

i'll get some for you tomorrow, my tranny crossmember is notched on the top.... ok cool thanks man.

[Ratrod25]

Hey lilflip did you ever get those exhaust shots?

[Turtle]

I wish the shop i worked at was close to yal. We were awsome at exhaust.Not tryn to brag just sayn. We did alot of street rods that had to be tucked up tight. Got good at it

[pacific coast]

This is on my 620 but you can see the pipe running above the torsion crossmember..the floor gets warm but i plan on installing a cat heat shield one day...
http://img.photobucket.com/albums/v605/markspics/Datsuns/ex1.jpg
http://img.photobucket.com/albums/v605/markspics/Datsuns/ex4.jpg

[Ratrod25]

This is on my 620 but you can see the pipe running above the torsion crossmember..the floor gets warm but i plan on installing a cat heat shield one day...
http://img.photobucket.com/albums/v605/markspics/Datsuns/ex1.jpg
Ok cool thanks!! :thumb: so you dont have any problems with the floor gettin hot?

[difl8ed]

i can get you pics of mine tomarrow when i finish it it will be wraped will fiberglass heat tape sence its about 1 inch from the floor also will have some heat shelds

[Ratrod25]

Would header rap work to keep the heat down?

[1lowda]

i just had to have mine redone i'll post some pics of it as soon as i get a chance

http://img190.imageshack.us/img190/9629/dsc00068sjb.jpg (http://img190.imageshack.us/i/dsc00068sjb.jpg/) http://img190.imageshack.us/img190/dsc00068sjb.jpg/1/w320.png (http://g.imageshack.us/img190/dsc00068sjb.jpg/1/)

http://img193.imageshack.us/img193/6634/dsc00067x.jpg (http://img193.imageshack.us/i/dsc00067x.jpg/) http://img193.imageshack.us/img193/dsc00067x.jpg/1/w320.png (http://g.imageshack.us/img193/dsc00067x.jpg/1/)

[difl8ed]

header wrap is the same thing just thiner exhust wrap comes 2-2.5 inches wide and you can get some with a spray that colors it and it also helps keep the heat down so im told not to sure about the paint keeping heat down. i posted the exhust pics on my thred if you want to see them not wraped yet but soon

[pacific coast]

Ok cool thanks!! :thumb: so you dont have any problems with the floor gettin hot?
Yeah it does get a bit warm,,plan on using a cat shield one day mounted under the cab.

[DISTURBEDPUP]

your under side looks like mine dose... is that a 1 off header too? i had one made cuz the pacesetter hung way down. i had a post on here and SSM seeing if any one wanted to buy a 1 off header wile the dude was at it. we trimmed the tranny and old tors bar X members like yours and made a new carrier berring Xmemb.... none of mine hangs below the frame! i dont have a full pipe pic's... just one or 2 of the under side of the header.http://i594.photobucket.com/albums/tt25/disturbedpup/nissan%20720/0520091149a.jpghttp://i594.photobucket.com/albums/tt25/disturbedpup/nissan%20720/0520091151.jpghttp://i594.photobucket.com/albums/tt25/disturbedpup/nissan%20720/0520091149b.jpg

[DISTURBEDPUP]

sorry man... didnt see where u said u got some pic's from me... i was thinkin wow that looks like mine. yes.... they hang way down. you can take the bottem off the stock exh manafold (keeping the upper )and have some shop make the rest where it dosent hang that far down. ohh and u might have to buy a collector(and they come in pairs because of V8's.thats why i was gonna make 2 and sell one.)other than that... u got cut cut cut all 3 X members. even my nissan hardbody hung down like that. best of luck... and she will lay all day and the pipe will never drag again.

[DISTURBEDPUP]

ohh i did have 2 header wrap from the flange... back about a foot.the pipe is tight and the E break and the speedO cable were all most layin on the pipe. not in the pic...

[Ratrod25]

lol thats funny!! I have a doug thorley long tube header so im going to try and just move the flange up on the pipe but i replaced my xmember thats in the middle of the truck.. So it just looks like you cut a notch in the torsion xmember i still have my torsions in, I wanted to get the exhaust done before i bag the front.. But looks like im going to have to do the front first.. Thanks for the pics fells's

[DISTURBEDPUP]

we did re-work the tranny Xmem and cut out the T-bar Xmem..... and the muff guys cut the top of the T-bar Xmem if u look close... kinda made a hole just enough for my 2 1/4 pipe! but it dose get tight over the trans cross member. me floor or bed gets hot... well it dose stop befor the rear end.

[Ratrod25]

Thanks for the pics man they helped alot! :thumb: I wanted to do my exhaust before i bag the front but having to cut the torsion Xmember wouldnt be good! lol

[lilFlip]

Hey lilflip did you ever get those exhaust shots?

sorry man...been busy, will try to get them tomorrow....

Hey man, sorry the truck is kind of pulled apart right now...tapping my T's to put my air gauges in and changing out the drain cock on my tank since it's leaking....I should have everything back together by this weekend, so I'll get them for you and post them up hopefully by this weekend.